Craftsman 536.88123 operating instructions Frozen Recoil Starter, Snow Throwing Tips

Page 14

FROZEN RECOIL STARTER

If the starter is frozen and will not turn engine:

•Pull as much rope out of the starter as possible.

•Release the starter handle and let it snap back against the starter.

If the starter still fails to turn engine, repeat the two previous steps until the starter en-

gages. Then continue with the directions for cold start.

To help prevent possible freeze-up of recoil starter and engine controls, proceed as fol- lows after each snow removal job.

•With the engine running, pull the starter rope hard with a continuous full arm stroke three or four times. Pulling of starter rope win produce a loud clattering sound, This is not harmful to the engine or starter.

•With the engine not running, wipe all snow and moisture from the carburetor cover in area of control levers. Also move throttle control, choke control, and starter handle several times.

A_ CAUTION: Never run engine indoors or in enclosed, poorly ventilated areas.

Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any

moving parts on engine and snow thrower.

WARNING: Temperature of muffler and nearby areas may exceed 150° F. Avoid these areas.

DO NOT allow children or young teenagers to operate or be near snow thrower while it is operating.

Z_ CAUTION: Do no attempt to remove any item that may become lodged in

auger without taking the following precau- tions:

•Release auger drive and traction drive levers.

•Move throttle lever to stop position.

•Remove (DO NOT TURN) ignition key.

•Disconnect spark plug wire.

•Do not place your hands in the auger or discharge chute, Use a pry bar.

SNOW THROWING TIPS

•For maximum snow thrower efficiency in

removing snow, adjust ground speed, NEVER the throttle. Go slower in deep, freezing, or wet snow. If the wheels slip, reduce forward speed. The engine is de-

signed to deliver maximum performance at full throttle and should be run at this

power setting at all times. Most efficient snow blowing is accomplished when the snow is removed immediately after it falls,

•For complete snow removal, slightly over- lap each path previously taken, Use more

overlap in deep snow to prevent overload- ing,

•The snow should be discharged down wind whenever possible. In windy condi- tions, lower the chute deflector to direct discharged snow close to the ground, where it is less likely to blow into un- wanted areas.

•For normal usage, set the skids so that the scraper bar is 1/8" above the skids. For extremely hard-packed snow sur- faces, adjust the skids upward so that the scraper bar touches the ground.

•On gravel or crushed rock surfaces, set the skids at 1-1/4" below the scraper bar (See To Adjust Skids Height paragraph on page 18). Stones and gravel must not be picked up and thrown by the machine.

•After the snow throwing job has been completed, allow the engine to idle for a few minutes, which will melt snow and ac- cumulated ice off the engine.

•Clean the snow thrower thoroughly after each use.

•Remove ice and snow accumulation and all debris from the entire snow thrower, and flush with water (if possible) to re- move all salt or other chemicals. Wipe snow thrower dry.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Snow Thrower Training Contents Service and Adjustments 18-22 Warranty StorageLimited TWO-YEAR Warranty on Craftsman Snow Thrower Preparation OperationFlatwasher Maintenance and StorageSteep sloping surfaces. do not USE Snow Thrower on Surfaces 8-16 Hex Jam NutsSpeed Lever Tools Required for AssemblyGlasses or eye shields while assembling snow thrower HOW to SET UP Your Snow Thrower To Installthe Upper Handle and CrankassemblySpeed Selector ROD AssembleReplace carriage bolt Remote Chute Control Knob HeadlightKnow Your Snow Thrower Chute Chute Deflector DeflectorTo Move Forward Backward Howto Useyour Snow ThrowerTo Control Snow Discharge To Stopyour SnowthrowerBefore Starting the Engine To Throw SnowTo USE Wheel Lockout PIN Checkthe OILFill GAS Cold StartTo Start Engine Recoil Starter Warm StartPush down on the starter button until Be sure the auger drive and traction driveGages. Then continue with the directions for cold start Frozen Recoil StarterSnow Throwing Tips For maximum snow thrower efficiencyCustomer Responsibilities Service Schedule Dates Records Lubrication ChartSnow Thrower After First USE Lubrication Every 10 HoursLubrication Before Storage After Each USEEngine Lubrication LubricationOIL Recommendation Spark PlugTo Adjustthe Clutch Control Cables To Adjust Skid HeightTo Adjust Scraper BAR Auger Drive Belt To Adjust BeltsTo Replace Belts Traction Drive BeltTo Adjustthe Belt Guide To Adjust the Friction WheelEnd nuts To Replace Friction WheelAuger Replace bottom panelTo Adjust To Adjust or Replace Spark PlugTo Adjust Carburetor To Replace Auger Shear BoltOther Snow Thrower StorageEngine Storage Steps belowTrouble Cause Correction

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents