Craftsman 536.88123 To Adjust Belts, To Replace Belts, Auger Drive Belt, Traction Drive Belt

Page 19

•Remove fuel from tank, and stand blower on end,

•Pull rubber boot off the top of the spdng. Push the cable through the spring (see

figure below) to expose the threaded por- tion of the cable.

Cable spring_

_

Square end

 

--

Locknut

•Hold the square end of the threaded por-

tion with pliers and adjust the Iocknut in or out until the excess slack is removed.

•Pull the cable back through the spring and connect the cable.

•Do the same for the other lever cable, if

needed.

NOTE: Whenever the traction drive or au-

ger belts are adjusted or replaced, the cables will need to be adjusted.

TO ADJUST BELTS

Belts stretch during normal use, If you need to adjust the belts due to wear or stretch, proceed as follows:

AUGER DRIVE BELT

If your snow thrower will not discharge snow, check the control cable adjustment. If it is correct, then check the condition of the

auger drive belt. It may be loose or dam- aged. If it is damaged, replace it (see To Replace Belts paragraph on this page).

TRACTION DRIVE BELT

The traction drive belt (see next figure) has constant spring pressure and does not re- quire adjustment.

•Replace the traction drive belt if it is slip- ping (see To Replace Belts paragraph on this page).

TO REPLACE BELTS

The drive belts on this snow thrower are of

special construction and should be replaced

with original equipment belts available from your nearest Craftsman Store or Service Center.

You will need the assistance of a second person while replacing the belts.

Drain the gasoline from the fuel tank by re- moving the fuel line at the carburetor. Drain the gas into a container and reinstall the

fuel line.

CAUTION: Drain the gasoline outdoors, away from the fire or flame.

AUGER DRIVE BELT

If your snow thrower will not discharge snow, and the auger drive belt (see figure below for location) is damaged, replace it as follows:

Au Drive Belt

er Drive

PulleyPulley

DrLveBeltiuide

Idler Pulley

Auger

Pulley

•Disconnect the spark plug wire.

•Remove the belt cover (See figure below).

Belt C_

1/4 X 1/2 In :hse f-tapping Screw

•Loosen the belt guide (see first figure this column) and pull away from the engine drive pulley.

•Loosen nut on the auger idler pulley (see first figure this column) and pull idler pulley away from the belt.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower Contents Service and Adjustments 18-22 Warranty StorageTraining Operation Preparation8-16 Hex Jam Nuts Maintenance and StorageSteep sloping surfaces. do not USE Snow Thrower on Surfaces FlatwasherGlasses or eye shields while assembling snow thrower Tools Required for AssemblySpeed Lever To Installthe Upper Handle and Crankassembly HOW to SET UP Your Snow ThrowerReplace carriage bolt AssembleSpeed Selector ROD Headlight Remote Chute Control KnobChute Chute Deflector Deflector Know Your Snow ThrowerTo Stopyour Snowthrower Howto Useyour Snow ThrowerTo Control Snow Discharge To Move Forward BackwardCheckthe OIL To Throw SnowTo USE Wheel Lockout PIN Before Starting the EngineCold Start Fill GASBe sure the auger drive and traction drive Warm StartPush down on the starter button until To Start Engine Recoil StarterFor maximum snow thrower efficiency Frozen Recoil StarterSnow Throwing Tips Gages. Then continue with the directions for cold startLubrication Chart Customer Responsibilities Service Schedule Dates RecordsAfter Each USE Lubrication Every 10 HoursLubrication Before Storage Snow Thrower After First USESpark Plug LubricationOIL Recommendation Engine LubricationTo Adjust Scraper BAR To Adjust Skid HeightTo Adjustthe Clutch Control Cables Traction Drive Belt To Adjust BeltsTo Replace Belts Auger Drive BeltTo Adjust the Friction Wheel To Adjustthe Belt GuideReplace bottom panel To Replace Friction WheelAuger End nutsTo Replace Auger Shear Bolt To Adjust or Replace Spark PlugTo Adjust Carburetor To AdjustSteps below Snow Thrower StorageEngine Storage OtherCorrection Trouble Cause

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.
Top Page Image Contents