Craftsman 536881851 manual Before Starting the Engine, Fill GAS, Check the OIL, Gasoline

Page 13

2.For ease of maneuverability in light snow conditions, disconnect the klick pin from the wheel locked position and push into the single wheel drive position (unlocked axle hole only). See Figure 12.

K]ick Pin

Unlocked

Single Wheel

Position

Drive

 

Figure 12

NOTE: Do not check the level of the oil while the engine runs,

2.Remove the oil fill cap/dipstick and wipe with a clean cloth.

3.Insert the oil fill cap/dipstick and turn clockwise to tighten.

4.Remove the oil fill cap/dipstick and check the oil.

5.If necessary, add oil until the oil reaches the FULL mark on the oil fill

cap/dipstick (see Figure 13). Do not add too much oil.

•OII FillCap/Dipstick

NOTE: Make sure that the klick pin is in the single wheel drive positionof the axle only and not throughthe locked position.

BEFORE STARTING THE ENGINE

tw Before you service or start the en- gine, familiarize yourself with the

snow thrower. Be sure you under- stand the function and location of all

controls.

. Check the tension of clutch cable before starting the engine. See To

Adjust The Control Cable para-

graph in the Service & Adjust- ments section of this manual.

,Be sure that all fasteners are tight.

4.Make sure the height adjust skids are properly adjusted. See To Ad- just Skid Height paragraph in the

Service & Adjustments section of this manual.

. Check tire pressure (14-17 pounds). Do not exceed maximum amount of pressure.

CHECK THE OIL:

NOTE: The engine was shippedfrom the factory filled with oil. Check the lev- el of the oil,Add oil as needed.

To Add Oil

1, Make sure the unit is level.

%

NOTE: level must be at the Full mark

Figure 13

6."Nghten the fill cap/dipstick securely each time you check the oil level.

NOTE: Synthetic oil can assist with starting in extreme cold temperatures. Synthetic 5W30 is acceptable for all temperatures. DO NOT mix oil with

gasoline.

FILL GAS:

This engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications).

fuels (called gasohol or

_ARNING: Alcohol blended those using ethanol or

methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel sys- tem of an engine while in storage.

NOTE: To avoid engine problems, the fuel system must be emptied before storage for 30 days Or longer. Start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See the Storage section in this manual for additional in- formation.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operators Manual Snow Thrower Safety Rules and Operating InstructionsSafety Rules Warranty StatementInternational Symbols AssemblyPreparation TrainingOperation Maintenance and Storage Control and Operating SymbolsSafetyWarningSymbols Contents of Parts BAG Actual Size To Remove Snow Thrower from Carton Tools Required for AssemblyCable back away from the motor Raise the upper handle intooperat- ing position To Assemble the Handle and Crank AssemblyHOW to SET the Length of the Cables HOW to Assemble the ChuteHOW to SET the Skid Height DeflectorAll assembly instructionshave been completed ChecklistKnow Your Snow Thrower To Control Snow Discharge HOW to Move Forward and BackwardTo USE Wheel Lockout PIN To Stop Your Snow ThrowerFill GAS Before Starting the EngineCheck the OIL To Add Oil Make sure the unit is levelTo Start Engine To Stop EngineBe stale from long periodsof storage in the container Position. Backfire or engine damagePage Frozen Starter Snow Throwing Tips To Remove Snow from AugerSnow should be discharged down windwhenever possible IO0 Customer ResponsibiutiesGeneral Recommendations After Each USESnow Thrower Engine SpecificationsAuger Drive Belt Chain Lubrication Every 25 HoursCheck the spark plug every twenty EnginePorcelain is cracked, or every Hours of useTo Adjust Scraper BAR To Adjust Skid HeightHOW to Remove Snow Hood Traction Drlve Belt Belt AdjustmentInstall the auger drive belt onto the engine pulley HOW to Replace the BeltsInstall the bolt cover. Tighten screw See Figure 18, Install the bottom panel seeTractionDrive Spring Disconnectthe spark plug wire HOW to Check Adjust the Cables Belt Guide AdjustmentAuger Drive Cable Adjustment Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin FrictionWheel in this section Install the bottom panel see FigureMake sure the hex shaft turns free- ly HOW to Replace Other Thoroughly clean the snowthrowerCause TroubleCorrection Where a warrantable condition exists Verter. Also includedmay be connectorsSystem on your enginefor the periodsof Time listedbelow,provided there has beenInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Key Craftsman 8.5HP Snow Thrower Engine16o Key Description Gear CaseCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels Pa No 772Page Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Key Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1Model 15A114-0342-E1 Briggs & Stratton Engin EBriggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine 100 Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIOPreparaci N CAPACITACI6NPREPARACIbN CapacitacionNecteel cabledela bujiay mantdngalo Mantenimiento Y AlmacenamientoSimbolos DE Control Y OPERACI6N Abajo SiMBOLOS DE Control Y OperacinContenido DE LA Bolsa DE Partes Iamaioreal Tarjeta de garantia no se muestraHerramientas Necesarias CMO Sacar EL Quitanieves DE LA CajaCMO Ensamblar EL Mango Y EL Conjunto DE LA ManivelaCMO Ajustar LOS Patines DE Altura CMO Ensamblar EL Deflector DEL Tubo DE DescargaCMO Establecer LA Longitud DE LOS Cables Usta DE REVISI6N Atr Conozca SU QuitanievesComoavanzary Retroceder Como Controlarla DescargadeLanzamientode Nieve Cmousar EL Pasadorde Enganchede LA RuedaAntes DE Encenderel Motor CombustibleAntes DE Arrancar EL Motor Para aadir aceiteArranquedel Motor Paradadel MotorC6mo hacer arrancarel motoren frio Manija del arranque manualse enrolle lentamente CGmohater arrancarun motor calienteConsejos Sobre EL Lanzamiento DE Nieve Comoquitarlanievey Escombrosatascadosde LabarrenaIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Valvula JuegodeLubricacin MotorAjustela barra raspadoraa la posici6n correcta Ajuste DE Labarra RaspadoraQuite el estrangulador vea la Figura Como Desmontar LA Cubierta ProtectoraVuelva a poner la cubierta de la correa Ajuste DE LAS CorreasPersona CMO Reemplazar I.AS CO- RreasPanel inferior Figura Afloje los pernos Cada lado delQuite el panel inferior Retire pemos Apriete los pernos a ambos lados del panel inferior CMO Revisar Y Ajustar LOS Cables Ajustes DE LA Correa GujaAjustes DEL Cable DE Propulsicn CMO Ajustar O Reemplazar LA Rueda DE Friccin Var ,*,nt,o,, oC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Motor QuitanievesCorrea de propulsi6npor tracci6nfioja o daSada Problema CausacorreccionUSO Page Page MY-HOME Matter Who made It, no matter who soldSears Parts and Repair Center Canada

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.
Top Page Image Contents