Craftsman 536881851 manual

Page 15

equipped with a three-wire

,_ WARNING: The starter is power cord and plug and is

designed to operate on 120 volt AC household current. It must be prop- erly grounded at all times to avoid the possibility of electrical shock which may be injurious to operator.

Follow all instructions carefully as sat forth in the "To Start En-

gine" section.

Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not sure. If your house wire system is not a three-wiresystem, do not use this electric starter un- der any conditions.

If your system is grounded and s three-hole receptacle is not avail- able at the point your starter will normally be used, one should be installed by a licensed electrician.

When connecting 120 volt AC

"Power Cord", always connect the cord to the Switch Box on the en-

gine first, then plug the other end into the three-hole grounded re- ceptacle. When disconnecting "Power Cord", always unplug the end In the three-hole grounded re- ceptacle first.

Choke Knob

Safety Key

 

Power Cord

 

 

Stop Switch

Recoil Starter

Receptacle

Handle

Figure 16

 

How To Start A Cold Engine

1.Be sure auger drive and traction drive levers are in the disengaged (RELEASED) position.

2.Push the stop switch to the ON position (see Figure 16).

3.Push in the safety key.

4.Rotate the choke knob to the CHOKE position.

5.(Electric Start) Plug the power cord into the starter motor on the en-

gine. Plug the other end of power cord into a three-hole, grounded 120 VOLT, AC receptacle.

6.Push the primer button as speci- fied below. Remove finger from primer button between pushes.

•Push two times if temperature is 15 ° F (-9 ° C) or higher.

•Push four times if temperature is below 15° F (-9 ° C).

7.(E/ecfric Start) Push down on the starter button u_l the engine starts.

To prolongthe life of the starter, do not crank for more than 5 seconds at a

time. Wait one minute between starts to allow the starter motor to cool.

,(Recoil Start) Slowly pull the recoil starter handle until resistance is

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operators Manual Snow Thrower Safety Rules and Operating InstructionsAssembly Warranty StatementSafety Rules International SymbolsTraining PreparationOperation Maintenance and Storage Control and Operating SymbolsSafetyWarningSymbols Contents of Parts BAG Actual Size Tools Required for Assembly To Remove Snow Thrower from CartonCable back away from the motor Raise the upper handle intooperat- ing position To Assemble the Handle and Crank AssemblyDeflector HOW to Assemble the ChuteHOW to SET the Length of the Cables HOW to SET the Skid HeightAll assembly instructionshave been completed ChecklistKnow Your Snow Thrower To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Control Snow Discharge To USE Wheel Lockout PINTo Add Oil Make sure the unit is level Before Starting the EngineFill GAS Check the OILPosition. Backfire or engine damage To Stop EngineTo Start Engine Be stale from long periodsof storage in the containerPage Frozen Starter To Remove Snow from Auger Snow Throwing TipsSnow should be discharged down windwhenever possible After Each USE Customer ResponsibiutiesIO0 General RecommendationsChain Lubrication Every 25 Hours Engine SpecificationsSnow Thrower Auger Drive BeltHours of use EngineCheck the spark plug every twenty Porcelain is cracked, or everyTo Adjust Scraper BAR To Adjust Skid HeightHOW to Remove Snow Hood Traction Drlve Belt Belt Adjustment18, Install the bottom panel see HOW to Replace the BeltsInstall the auger drive belt onto the engine pulley Install the bolt cover. Tighten screw See FigureTractionDrive Spring Disconnectthe spark plug wire Belt Guide Adjustment HOW to Check Adjust the CablesAuger Drive Cable Adjustment Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin Install the bottom panel see Figure FrictionWheel in this sectionMake sure the hex shaft turns free- ly HOW to Replace Other Thoroughly clean the snowthrowerTrouble CauseCorrection Time listedbelow,provided there has been Verter. Also includedmay be connectorsWhere a warrantable condition exists System on your enginefor the periodsofInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Key Craftsman 8.5HP Snow Thrower Engine16o Key Description Gear CaseCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels Pa No 772Page Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Key Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1Model 15A114-0342-E1 Briggs & Stratton Engin EBriggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine 100 Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIOPreparaci N CAPACITACI6NPREPARACIbN CapacitacionNecteel cabledela bujiay mantdngalo Mantenimiento Y AlmacenamientoSimbolos DE Control Y OPERACI6N Abajo SiMBOLOS DE Control Y OperacinContenido DE LA Bolsa DE Partes Iamaioreal Tarjeta de garantia no se muestraHerramientas Necesarias CMO Sacar EL Quitanieves DE LA CajaCMO Ensamblar EL Mango Y EL Conjunto DE LA ManivelaCMO Ensamblar EL Deflector DEL Tubo DE Descarga CMO Ajustar LOS Patines DE AlturaCMO Establecer LA Longitud DE LOS Cables Usta DE REVISI6N Atr Conozca SU QuitanievesCmousar EL Pasadorde Enganchede LA Rueda Como Controlarla DescargadeComoavanzary Retroceder Lanzamientode NievePara aadir aceite CombustibleAntes DE Encenderel Motor Antes DE Arrancar EL MotorArranquedel Motor Paradadel MotorC6mo hacer arrancarel motoren frio Manija del arranque manualse enrolle lentamente CGmohater arrancarun motor calienteConsejos Sobre EL Lanzamiento DE Nieve Comoquitarlanievey Escombrosatascadosde LabarrenaIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Valvula JuegodeLubricacin MotorAjustela barra raspadoraa la posici6n correcta Ajuste DE Labarra RaspadoraQuite el estrangulador vea la Figura Como Desmontar LA Cubierta ProtectoraCMO Reemplazar I.AS CO- Rreas Ajuste DE LAS CorreasVuelva a poner la cubierta de la correa PersonaAfloje los pernos Cada lado del Panel inferior FiguraQuite el panel inferior Retire pemos Apriete los pernos a ambos lados del panel inferior CMO Revisar Y Ajustar LOS Cables Ajustes DE LA Correa GujaAjustes DEL Cable DE Propulsicn CMO Ajustar O Reemplazar LA Rueda DE Friccin Var ,*,nt,o,, oC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Motor QuitanievesCorrea de propulsi6npor tracci6nfioja o daSada Problema CausacorreccionUSO Page Page Canada Matter Who made It, no matter who soldMY-HOME Sears Parts and Repair Center

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.
Top Page Image Contents