Craftsman 536881851 manual To Remove Snow from Auger, Snow Throwing Tips

Page 17

TO REMOVE SNOW FROM AUGER

to remove snow or debris

. ARNING: Do not attempt that may become lodged in

auger with your hands. Use the cleaning stick to remove snow or debris.

A cleaning stick is attached to the top of the auger housing. Use the cleaning

SNOW THROWING TIPS

1.For maximum snow thrower efficien- cy in removing snow, adjust ground speed. Go slower in deep, freezing or wet snow. If the wheels slips, re- duce forward speed.

2.Most efficientsnow throwingis ac- complishedwhen the snow is re- moved immediately after if falls.

3.For complete snow removal, slightly ovedap each path previouslytaken.

4.The snow should be discharged down windwhenever possible.

5..For normal usage, set the skids so that the scraper bar is 1/8" above the skids. For extremely hard- packed snow surfaces, adjust the skids upward so that the scraper bar touchesthe ground.

6. On gravel or crushed rock surfaces,

stickto remove snowfrom the auger housing.

•Release auger drive lever.

•Remove (do not turn) safety key.

•Disconnectspark plug wire.

•Do not place your hands in the au- ger or dischargechute. Use the cleaning stickto remove snow.

set the skids at 1-1/4" below the scraper bar. See To Adjust Skid Height paragraph in the Service & Adjustments section of this manu- al. Rocks and gravel must not be

picked up and thrown by the ma- chine.

. After the snow throwing job has been completed, allow the engine to idle for a few minutes, which will melt snow and accumulated ice off

the engine.

. Clean the snow thrower thoroughly after each use.

9.Remove ice and snow accumulation and all debris from the entire snow thrower, and flushwith water (if pos- sible) to remove all salt or other chemicals. Wipe snow thrower dry.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operators Manual Snow Thrower Safety Rules and Operating InstructionsSafety Rules Warranty StatementInternational Symbols AssemblyOperation TrainingPreparation Maintenance and Storage Control and Operating SymbolsSafetyWarningSymbols Contents of Parts BAG Actual Size Cable back away from the motor Tools Required for AssemblyTo Remove Snow Thrower from Carton Raise the upper handle intooperat- ing position To Assemble the Handle and Crank AssemblyHOW to SET the Length of the Cables HOW to Assemble the ChuteHOW to SET the Skid Height DeflectorAll assembly instructionshave been completed ChecklistKnow Your Snow Thrower To Control Snow Discharge HOW to Move Forward and BackwardTo USE Wheel Lockout PIN To Stop Your Snow ThrowerFill GAS Before Starting the EngineCheck the OIL To Add Oil Make sure the unit is levelTo Start Engine To Stop EngineBe stale from long periodsof storage in the container Position. Backfire or engine damagePage Frozen Starter Snow should be discharged down windwhenever possible To Remove Snow from AugerSnow Throwing Tips IO0 Customer ResponsibiutiesGeneral Recommendations After Each USESnow Thrower Engine SpecificationsAuger Drive Belt Chain Lubrication Every 25 HoursCheck the spark plug every twenty EnginePorcelain is cracked, or every Hours of useTo Adjust Scraper BAR To Adjust Skid HeightHOW to Remove Snow Hood Traction Drlve Belt Belt AdjustmentInstall the auger drive belt onto the engine pulley HOW to Replace the BeltsInstall the bolt cover. Tighten screw See Figure 18, Install the bottom panel seeTractionDrive Spring Disconnectthe spark plug wire Auger Drive Cable Adjustment Belt Guide AdjustmentHOW to Check Adjust the Cables Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin Make sure the hex shaft turns free- ly Install the bottom panel see FigureFrictionWheel in this section HOW to Replace Other Thoroughly clean the snowthrowerCorrection TroubleCause Where a warrantable condition exists Verter. Also includedmay be connectorsSystem on your enginefor the periodsof Time listedbelow,provided there has beenInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Key Craftsman 8.5HP Snow Thrower Engine16o Key Description Gear CaseCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels Pa No 772Page Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Key Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1Model 15A114-0342-E1 Briggs & Stratton Engin EBriggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine 100 Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIOPreparaci N CAPACITACI6NPREPARACIbN CapacitacionNecteel cabledela bujiay mantdngalo Mantenimiento Y AlmacenamientoSimbolos DE Control Y OPERACI6N Abajo SiMBOLOS DE Control Y OperacinContenido DE LA Bolsa DE Partes Iamaioreal Tarjeta de garantia no se muestraHerramientas Necesarias CMO Sacar EL Quitanieves DE LA CajaCMO Ensamblar EL Mango Y EL Conjunto DE LA ManivelaCMO Establecer LA Longitud DE LOS Cables CMO Ensamblar EL Deflector DEL Tubo DE DescargaCMO Ajustar LOS Patines DE Altura Usta DE REVISI6N Atr Conozca SU QuitanievesComoavanzary Retroceder Como Controlarla DescargadeLanzamientode Nieve Cmousar EL Pasadorde Enganchede LA RuedaAntes DE Encenderel Motor CombustibleAntes DE Arrancar EL Motor Para aadir aceiteArranquedel Motor Paradadel MotorC6mo hacer arrancarel motoren frio Manija del arranque manualse enrolle lentamente CGmohater arrancarun motor calienteConsejos Sobre EL Lanzamiento DE Nieve Comoquitarlanievey Escombrosatascadosde LabarrenaIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Valvula JuegodeLubricacin MotorAjustela barra raspadoraa la posici6n correcta Ajuste DE Labarra RaspadoraQuite el estrangulador vea la Figura Como Desmontar LA Cubierta ProtectoraVuelva a poner la cubierta de la correa Ajuste DE LAS CorreasPersona CMO Reemplazar I.AS CO- RreasQuite el panel inferior Afloje los pernos Cada lado delPanel inferior Figura Retire pemos Apriete los pernos a ambos lados del panel inferior CMO Revisar Y Ajustar LOS Cables Ajustes DE LA Correa GujaAjustes DEL Cable DE Propulsicn CMO Ajustar O Reemplazar LA Rueda DE Friccin Var ,*,nt,o,, oC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Motor QuitanievesCorrea de propulsi6npor tracci6nfioja o daSada Problema CausacorreccionUSO Page Page MY-HOME Matter Who made It, no matter who soldSears Parts and Repair Center Canada

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.
Top Page Image Contents