Craftsman 536881851 manual To Adjust Skid Height, To Adjust Scraper BAR

Page 21

nect the spark plug wire and

AARNING: Always discon- place it where it cannot

make contact with spark plug to pre- vent accidental starting when mak- ing any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the outside of the auger housing. See Figure 20.

These skids elevate the front of the snow thrower.

Nuts

.O

Height Adjust Skid

Figure 20

For normal hard surfaces, such as a paved driveway or walk, adjust the skids as follows.

1.Position the snow thrower on a level surface.

. Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi- mum inflation. Do not exceed maxi-

mum sidewall pressure on tire.

3.Place the extra shear bolts supplied with the unit under each end of the

scraper bar next to the adjustable skids.

4.Loosen the mounting nuts that hold the adjustable skids. To bring the front of the snow thrower down,

raise the adjustable skids. _ghten the mounting nuts. See Figure 20.

NOTE: For rocky or uneven surfaces, raise the front of the snow thrower by moving the skids down.

maintain proper ground

AARNING: Be certain to clearance for your particular

area to be cleared. Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force to cause personal injury, property damage or damage to the snow thrower.

TO ADJUST SCRAPER BAR

After considerableuse, the metal scrap- er bar will have a definitewear pattem. The scraper bar in conjunctionwith the skids shouldalways be adjusted to al- low 1/8" between the scraper bar and the sidewalk or area to be cleaned.

1.Positionthe snow thrower on a level surface.

. Make sure both tires are equally in- flated. Proper tire pressure is 14 to 17 PSI. See side of tire for maxi-

mum inflation. Do not exceed maxi-

mum sidewall pressure on tire.

3.Loosen the carriage bolts and nuts securingthe scraper bar to the au- ger housing.

4.Adjust the scraper bar to the proper position.

5."13ghtenthe carriage boltsand nuts, making sure that the scraper bar is parallel with the workingsurface.

1For extended operation, the scraper bar may be reversed. If the scraper bar must be replaceddue to wear, remove the carriage boltsand nuts and installa new scraper bar.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operators Manual Snow Thrower Safety Rules and Operating InstructionsSafety Rules Warranty StatementInternational Symbols AssemblyTraining PreparationOperation Maintenance and Storage Control and Operating SymbolsSafetyWarningSymbols Contents of Parts BAG Actual Size Tools Required for Assembly To Remove Snow Thrower from CartonCable back away from the motor Raise the upper handle intooperat- ing position To Assemble the Handle and Crank AssemblyHOW to SET the Length of the Cables HOW to Assemble the ChuteHOW to SET the Skid Height DeflectorAll assembly instructionshave been completed ChecklistKnow Your Snow Thrower To Control Snow Discharge HOW to Move Forward and BackwardTo USE Wheel Lockout PIN To Stop Your Snow ThrowerFill GAS Before Starting the EngineCheck the OIL To Add Oil Make sure the unit is levelTo Start Engine To Stop EngineBe stale from long periodsof storage in the container Position. Backfire or engine damagePage Frozen Starter To Remove Snow from Auger Snow Throwing TipsSnow should be discharged down windwhenever possible IO0 Customer ResponsibiutiesGeneral Recommendations After Each USESnow Thrower Engine SpecificationsAuger Drive Belt Chain Lubrication Every 25 HoursCheck the spark plug every twenty EnginePorcelain is cracked, or every Hours of useTo Adjust Scraper BAR To Adjust Skid HeightHOW to Remove Snow Hood Traction Drlve Belt Belt AdjustmentInstall the auger drive belt onto the engine pulley HOW to Replace the BeltsInstall the bolt cover. Tighten screw See Figure 18, Install the bottom panel seeTractionDrive Spring Disconnectthe spark plug wire Belt Guide Adjustment HOW to Check Adjust the CablesAuger Drive Cable Adjustment Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin Install the bottom panel see Figure FrictionWheel in this sectionMake sure the hex shaft turns free- ly HOW to Replace Other Thoroughly clean the snowthrowerTrouble CauseCorrection Where a warrantable condition exists Verter. Also includedmay be connectorsSystem on your enginefor the periodsof Time listedbelow,provided there has beenInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Key Craftsman 8.5HP Snow Thrower Engine16o Key Description Gear CaseCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels Pa No 772Page Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Key Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1Model 15A114-0342-E1 Briggs & Stratton Engin EBriggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine 100 Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIOPreparaci N CAPACITACI6NPREPARACIbN CapacitacionNecteel cabledela bujiay mantdngalo Mantenimiento Y AlmacenamientoSimbolos DE Control Y OPERACI6N Abajo SiMBOLOS DE Control Y OperacinContenido DE LA Bolsa DE Partes Iamaioreal Tarjeta de garantia no se muestraHerramientas Necesarias CMO Sacar EL Quitanieves DE LA CajaCMO Ensamblar EL Mango Y EL Conjunto DE LA ManivelaCMO Ensamblar EL Deflector DEL Tubo DE Descarga CMO Ajustar LOS Patines DE AlturaCMO Establecer LA Longitud DE LOS Cables Usta DE REVISI6N Atr Conozca SU QuitanievesComoavanzary Retroceder Como Controlarla DescargadeLanzamientode Nieve Cmousar EL Pasadorde Enganchede LA RuedaAntes DE Encenderel Motor CombustibleAntes DE Arrancar EL Motor Para aadir aceiteArranquedel Motor Paradadel MotorC6mo hacer arrancarel motoren frio Manija del arranque manualse enrolle lentamente CGmohater arrancarun motor calienteConsejos Sobre EL Lanzamiento DE Nieve Comoquitarlanievey Escombrosatascadosde LabarrenaIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Valvula JuegodeLubricacin MotorAjustela barra raspadoraa la posici6n correcta Ajuste DE Labarra RaspadoraQuite el estrangulador vea la Figura Como Desmontar LA Cubierta ProtectoraVuelva a poner la cubierta de la correa Ajuste DE LAS CorreasPersona CMO Reemplazar I.AS CO- RreasAfloje los pernos Cada lado del Panel inferior FiguraQuite el panel inferior Retire pemos Apriete los pernos a ambos lados del panel inferior CMO Revisar Y Ajustar LOS Cables Ajustes DE LA Correa GujaAjustes DEL Cable DE Propulsicn CMO Ajustar O Reemplazar LA Rueda DE Friccin Var ,*,nt,o,, oC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Motor QuitanievesCorrea de propulsi6npor tracci6nfioja o daSada Problema CausacorreccionUSO Page Page MY-HOME Matter Who made It, no matter who soldSears Parts and Repair Center Canada

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.
Top Page Image Contents