Craftsman 536881851 manual Belt Adjustment, Traction Drlve Belt

Page 23

BELT ADJUSTMENT

Traction Drlve Belt

The tractiondrive belt has constant spring pressure and does not require an adjustment. If the traction drive belt is slipping, replace the belt. See =How To Replace The Belts" in the Service And Adjustment section.

Auger Drive Belt

If your snow blower will not discharge snow, check the control cable adjust- ment. If it is correct, then check the condition of the auger drive belt. If it is damaged or loose, replace it (see "How To Replace The Belts" in this section of the manual).

1.Disconnect spark plug wire.

2.Remove screw from belt coven Remove belt cover (see Figure 25).

25

. Loosen nut on auger idler pulley and move auger idler pulley towards belt about 1/8 inch (3 mm) (see Figure 29).

4."13ghtennut.

. Have someone engage auger drive clutch. Check tension on belt (op- posite idler pulley). Belt shouldde- flect about 1/2 inch (12.5 mm) with moderate pressure (Figure 26). You may have to move idler pulley more than once to obtain the correctten- sion.

 

 

 

 

Auger

 

 

,_

 

EDngiVnee

 

 

-_

 

Pulley

 

 

J

_O

1/2 inch

 

t

 

",\_

(12.5mm)

Idler.....-,.([

..i',,_ I''_

Deflection

Pulley

7

"_

",\

 

• Engaged

/.___.___

 

 

Figure 26

6.Reinstall belt cover.

. Whenever belts are adjustedor re- placed, the cables will need to be adjusted. (See Cable Adjustmentin this section of the manual).

8.Attach the spark plug wire.

23

Image 23
Contents Operators Manual Snow Thrower Safety Rules and Operating InstructionsAssembly Warranty StatementSafety Rules International SymbolsOperation TrainingPreparation Maintenance and Storage Control and Operating SymbolsSafetyWarningSymbols Contents of Parts BAG Actual Size Cable back away from the motor Tools Required for AssemblyTo Remove Snow Thrower from Carton Raise the upper handle intooperat- ing position To Assemble the Handle and Crank AssemblyDeflector HOW to Assemble the ChuteHOW to SET the Length of the Cables HOW to SET the Skid HeightAll assembly instructionshave been completed ChecklistKnow Your Snow Thrower To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Control Snow Discharge To USE Wheel Lockout PINTo Add Oil Make sure the unit is level Before Starting the EngineFill GAS Check the OILPosition. Backfire or engine damage To Stop EngineTo Start Engine Be stale from long periodsof storage in the containerPage Frozen Starter Snow should be discharged down windwhenever possible To Remove Snow from AugerSnow Throwing Tips After Each USE Customer ResponsibiutiesIO0 General RecommendationsChain Lubrication Every 25 Hours Engine SpecificationsSnow Thrower Auger Drive BeltHours of use EngineCheck the spark plug every twenty Porcelain is cracked, or everyTo Adjust Scraper BAR To Adjust Skid HeightHOW to Remove Snow Hood Traction Drlve Belt Belt Adjustment18, Install the bottom panel see HOW to Replace the BeltsInstall the auger drive belt onto the engine pulley Install the bolt cover. Tighten screw See FigureTractionDrive Spring Disconnectthe spark plug wire Auger Drive Cable Adjustment Belt Guide AdjustmentHOW to Check Adjust the Cables Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin Make sure the hex shaft turns free- ly Install the bottom panel see FigureFrictionWheel in this section HOW to Replace Other Thoroughly clean the snowthrowerCorrection TroubleCause Time listedbelow,provided there has been Verter. Also includedmay be connectorsWhere a warrantable condition exists System on your enginefor the periodsofInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Key Craftsman 8.5HP Snow Thrower Engine16o Key Description Gear CaseCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels Pa No 772Page Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Key Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1Model 15A114-0342-E1 Briggs & Stratton Engin EBriggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine 100 Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIOPreparaci N CAPACITACI6NPREPARACIbN CapacitacionNecteel cabledela bujiay mantdngalo Mantenimiento Y AlmacenamientoSimbolos DE Control Y OPERACI6N Abajo SiMBOLOS DE Control Y OperacinContenido DE LA Bolsa DE Partes Iamaioreal Tarjeta de garantia no se muestraHerramientas Necesarias CMO Sacar EL Quitanieves DE LA CajaCMO Ensamblar EL Mango Y EL Conjunto DE LA ManivelaCMO Establecer LA Longitud DE LOS Cables CMO Ensamblar EL Deflector DEL Tubo DE DescargaCMO Ajustar LOS Patines DE Altura Usta DE REVISI6N Atr Conozca SU QuitanievesCmousar EL Pasadorde Enganchede LA Rueda Como Controlarla DescargadeComoavanzary Retroceder Lanzamientode NievePara aadir aceite CombustibleAntes DE Encenderel Motor Antes DE Arrancar EL MotorArranquedel Motor Paradadel MotorC6mo hacer arrancarel motoren frio Manija del arranque manualse enrolle lentamente CGmohater arrancarun motor calienteConsejos Sobre EL Lanzamiento DE Nieve Comoquitarlanievey Escombrosatascadosde LabarrenaIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Valvula JuegodeLubricacin MotorAjustela barra raspadoraa la posici6n correcta Ajuste DE Labarra RaspadoraQuite el estrangulador vea la Figura Como Desmontar LA Cubierta ProtectoraCMO Reemplazar I.AS CO- Rreas Ajuste DE LAS CorreasVuelva a poner la cubierta de la correa PersonaQuite el panel inferior Afloje los pernos Cada lado delPanel inferior Figura Retire pemos Apriete los pernos a ambos lados del panel inferior CMO Revisar Y Ajustar LOS Cables Ajustes DE LA Correa GujaAjustes DEL Cable DE Propulsicn CMO Ajustar O Reemplazar LA Rueda DE Friccin Var ,*,nt,o,, oC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Motor QuitanievesCorrea de propulsi6npor tracci6nfioja o daSada Problema CausacorreccionUSO Page Page Canada Matter Who made It, no matter who soldMY-HOME Sears Parts and Repair Center

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.