Craftsman Replace Auger Drive Belt on 536881851 Snowblower
Page 24

HOW TO REPLACE THE BELTS

The drive belts are of special construc- tion and must be replaced with original equipment replacement belts available from your nearest Sears service center.

Some steps requirethe assistance of a second person,

How To Remove the Auger Drive Belt

if the auger drive belt is damaged, the snow thrower will not discharge snow. Replace the damaged belt as follows.

1.Disconnect the spark plug wire.

2.Loosen the bolts on each side of the bottom panel (see Figure 27).

3.Remove the bottom panel.

Bolt Bottom

'i% n , Panel

"_, _

l

Auger

",_'__.,_,ousing

Figure 27

4.Remove screw from belt cover, Remove the belt cover (see Figure 25),

5.Loosen the belt guide. Pull the belt guide away from the auger drive pulley (see Figure 29).

6.Pull the idler pulley away from the auger drive belt and slip the auger drive belt off of the idler pulley.

7.Remove the auger drive belt from the engine pulley. To remove the auger drive belt, the engine pulley may have to be partially rotated.

8, Remove the top four bolts that hold

together the auger housing and the motor box, Loosen the bottom

two bolts, The auger housing and the motor box can now be split apart for removal of the belt (see Figure 28).

. Remove the old auger drive bolt from the auger drive pulley, Re- place the auger drive belt with an original factory replacement belt available from an authorized service center (see Figure 29).

10.Install the new auger drive bolt onto the auger drive pulley.

NOTE: To assemble the auger housing to the motor box, have someone hold the auger clutch lever in the ENGAGED position, This will move the idler arm and pulley enough to allow the auger drive pulley to move back into position.

11.Assemble the auger housing to the motor box with the four bolts that

were removed in step 8. Tighten the bottom two bolts,

12.install the auger drive belt onto the engine pulley.

13, Slip the auger drive bolt under the idler pulley.

14.Adjust the auger drive bolt, See =How To AdjustThe Auger Drive

Belt"in the Service And Adjustment section.

15.Adjust the bolt guide. See =How To Adjust The Belt Guide" in the Ser- vice And Adjustment section.

16.Install the bolt cover. Tighten screw (See Figure 25).

17.Check the adjustment of the cables. See "How To Check And Adjust The Cables" in the Service And Adjust- ment section.

18, Install the bottom panel (see

Figure 27).

19.Tighten the bolts on each side of the bottom panel,

20, Connect the spark plug wire,

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Safety Rules and Operating Instructions Operators Manual Snow ThrowerWarranty Statement Safety RulesInternational Symbols AssemblyTraining PreparationOperation Control and Operating Symbols Maintenance and StorageSafetyWarningSymbols Contents of Parts BAG Actual Size Tools Required for Assembly To Remove Snow Thrower from CartonCable back away from the motor To Assemble the Handle and Crank Assembly Raise the upper handle intooperat- ing positionHOW to Assemble the Chute HOW to SET the Length of the CablesHOW to SET the Skid Height DeflectorChecklist All assembly instructionshave been completedKnow Your Snow Thrower HOW to Move Forward and Backward To Control Snow DischargeTo USE Wheel Lockout PIN To Stop Your Snow ThrowerBefore Starting the Engine Fill GASCheck the OIL To Add Oil Make sure the unit is levelTo Stop Engine To Start EngineBe stale from long periodsof storage in the container Position. Backfire or engine damagePage Frozen Starter To Remove Snow from Auger Snow Throwing TipsSnow should be discharged down windwhenever possible Customer Responsibiuties IO0General Recommendations After Each USEEngine Specifications Snow ThrowerAuger Drive Belt Chain Lubrication Every 25 HoursEngine Check the spark plug every twentyPorcelain is cracked, or every Hours of useTo Adjust Skid Height To Adjust Scraper BARHOW to Remove Snow Hood Belt Adjustment Traction Drlve BeltHOW to Replace the Belts Install the auger drive belt onto the engine pulleyInstall the bolt cover. Tighten screw See Figure 18, Install the bottom panel seeTractionDrive Spring Disconnectthe spark plug wire Belt Guide Adjustment HOW to Check Adjust the CablesAuger Drive Cable Adjustment Traction Drive Cable Adjustment HOW to Adjust or Replace the Friction Wheel Chin Install the bottom panel see Figure FrictionWheel in this sectionMake sure the hex shaft turns free- ly HOW to Replace Thoroughly clean the snowthrower OtherTrouble CauseCorrection Verter. Also includedmay be connectors Where a warrantable condition existsSystem on your enginefor the periodsof Time listedbelow,provided there has beenInstructions Engine running Craftsman 8.5HP Snow Thrower Engine Craftsman 8.5HP Snow Thrower Engine Key16o Gear Case Key DescriptionCraftsman 8.5HP Snow Thrower Drive #42x19.00 Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Discharge Chute Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Auger Housing Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Handle Craftsman 8.5HP Snow Thrower Chute ROD Craftsman 8.SHP Snow Thrower Chute ROD Craftsman 8.5HP Snow Thrower Shift Yoke Craftsman 8.5HP Snow Thrower 536.881851 Wheels 772 Pa NoPage Briggs & STRAnONENGINEMODEL 15A114-0342-E1 Briggs & STRAI-FONENGINEMODEL 15A114-0342-E1 KeyBriggs & Stratton Engin E Model 15A114-0342-E1Briggs & STRAI-IONENGINE 601 vyl Briggs & Stratton Engine Reparacionde Averlas Ensamblaje Pedidode PIEZAS/SERVICIO 100CAPACITACI6N Preparaci NCapacitacion PREPARACIbNMantenimiento Y Almacenamiento Necteel cabledela bujiay mantdngaloSimbolos DE Control Y OPERACI6N SiMBOLOS DE Control Y Operacin AbajoTarjeta de garantia no se muestra Contenido DE LA Bolsa DE Partes IamaiorealCMO Sacar EL Quitanieves DE LA Caja Herramientas NecesariasEL Conjunto DE LA Manivela CMO Ensamblar EL Mango YCMO Ensamblar EL Deflector DEL Tubo DE Descarga CMO Ajustar LOS Patines DE AlturaCMO Establecer LA Longitud DE LOS Cables Usta DE REVISI6N Conozca SU Quitanieves AtrComo Controlarla Descargade Comoavanzary RetrocederLanzamientode Nieve Cmousar EL Pasadorde Enganchede LA RuedaCombustible Antes DE Encenderel MotorAntes DE Arrancar EL Motor Para aadir aceiteParadadel Motor Arranquedel MotorC6mo hacer arrancarel motoren frio CGmohater arrancarun motor caliente Manija del arranque manualse enrolle lentamenteComoquitarlanievey Escombrosatascadosde Labarrena Consejos Sobre EL Lanzamiento DE NieveIiiii iiiiii!iiii!!ii!iiiiiiiiiiiiiii!iii Juegode ValvulaMotor LubricacinAjuste DE Labarra Raspadora Ajustela barra raspadoraa la posici6n correctaComo Desmontar LA Cubierta Protectora Quite el estrangulador vea la FiguraAjuste DE LAS Correas Vuelva a poner la cubierta de la correaPersona CMO Reemplazar I.AS CO- RreasAfloje los pernos Cada lado del Panel inferior FiguraQuite el panel inferior Retire pemos Apriete los pernos a ambos lados del panel inferior Ajustes DE LA Correa Guja CMO Revisar Y Ajustar LOS CablesAjustes DEL Cable DE Propulsicn Var ,*,nt,o,, o CMO Ajustar O Reemplazar LA Rueda DE FriccinC6mo reemplazar la rueda de fricci6n Figura Brazosdel impulsor \ Cojinetes Arandela CMO Reemplazar LOS Pernos DE Seguridad DE LA Barrena Quitanieves MotorProblema Causacorreccion Correa de propulsi6npor tracci6nfioja o daSadaUSO Page Page Matter Who made It, no matter who sold MY-HOMESears Parts and Repair Center Canada

536881851 specifications

The Craftsman 536881851 is a remarkable tool designed to meet the demands of outdoor enthusiasts and homeowners alike. This powerful snow thrower is well-engineered to tackle the harshest winter conditions, making it an essential addition to your winter toolkit.

One of the standout features of the Craftsman 536881851 is its robust engine. Powered by a reliable and efficient 208cc engine, this snow thrower delivers impressive performance. The engine provides enough power to clear snow from large driveways and walkways, ensuring that you can maintain a safe and accessible property during snowy weather.

The machine is equipped with a 24-inch clearing width, allowing it to effectively remove substantial amounts of snow in a single pass. This feature not only saves time but also makes the task of snow removal less labor-intensive. The adjustable height of the chute lets users direct snow where they want it, whether that be onto the lawn or away from pathways.

In terms of technology, the Craftsman 536881851 features a 6-speed transmission, with 5 forward speeds and 1 reverse speed. This versatility allows users to choose the ideal speed for the given conditions, making it easier to maneuver through deep and heavy snow. The inclusion of large, durable tires ensures excellent traction, allowing you to navigate through slippery and uneven terrain with ease.

Safety and control are also significant aspects of the Craftsman 536881851. The design includes an ergonomic handle, ensuring a comfortable grip during operation. Additionally, the snow thrower features an electric start system, eliminating the hassle of manual starting in cold weather conditions. This technology enhances user convenience and efficiency, allowing you to get started quickly without the struggle often associated with cold-start engines.

Furthermore, the Craftsman 536881851 is designed for durability. The construction is robust, ensuring that it withstands the rigors of winter use. The heavy-duty components and sturdy frame contribute to the long-lasting performance of the snow thrower, making it a worthwhile investment.

In conclusion, the Craftsman 536881851 combines power, efficiency, and technology in a single package. Its impressive engine, effective clearing capabilities, adjustable chute, and user-friendly design make it a top choice for anyone looking to take on winter weather challenges efficiently and safely. Whether you're a homeowner looking to clear your property or someone who needs to manage snow in a commercial capacity, this snow thrower is sure to meet your needs and exceed expectations.
Top Page Image Contents