Craftsman 536.886141 Lubrication Chart, Snow Thrower Lubrication Every 25 Hours, After First USE

Page 15

GENERAL RECOMMENDATIONS

The warranty on this snow thrower does not cover items that have been subjected to op- erator abuse or negligence. To receive full value from the warranty, the operator must maintain the snow thrower as instructed in this manual. The maintenance chart is pro- vided to assist the operator in properly maintaining the snow thrower.

Some adjustments will need to be made pe-

riodically to properly maintain your snow thrower.

AFTER FIRST USE

•Check for any loose or damaged parts.

•Tighten any loose fasteners.

°Check and maintain the auger.

•After each use, remove all snow and slush off the snow thrower to prevent freezing of auger or controls.

•Check controls to make sure they are functioning properly.

°If any parts are worn or damaged, replace immediately.

LUBRICATION CHART

Lubricate

Disc Drive

Plate Zerk

with a Hi

Temp

Moly

Grease,

SNOW THROWER

LUBRICATION - EVERY 25 HOURS

o Lubricate Disc Drive Plate every twenty-five

(25)hours and atthe end of the season and/ or before storage.

To Lubricate:

o Position speed selector lever in first gear.

•Stand the snow thrower up on the auger housing end.

°Remov_ the bottom panel (see second figure on page 19 ).

FdctionShaft

WheelDisc

(Require

No ,' LubricatiOn)

Friction
Wheel	Grease
\	Bearing
	Place coin in gap
	between fdction
	wheel and disc drive	Point at wh grease
-/plate		shoutd be visible

I!

_GreaseZerk

°"]'urn disc drive plate clockwise by hand until grease zerk is clearly visible at front center. See figure below.

o Place a coin or (a shim of equal thick- ness) between the rubber friction wheel and disc drive plate to prevent rubber fric- tion wheel contacting the drive disc.

•To grease zerk, use a hand grease gun, lubricate with a Hi'Tamp EP Moly grease See inset of second figure on this page.

DO NOT over fill or allow grease to come in contact with the disc drive plate or fric- tion wheel or damage will result, Fill zerk only until grease becomes visible below bearing assembly located under grease zerk. See insert in figure above_

IMPORTANT" Remove coin and ensure that a gap exists between friction wheel and disc drive plate.

NOTE: Clean all excess grease found on friction disc hub.

CAUTION: Do not allow grease to contact friction wheel and disc drive plate.

15

Image 15

Contents Snow Thrower Training ServiceLimited TWO-YEAR Warranty on Craftsman Snow Thrower PreparationOperation Starter Motor Cord 10Ft Maintenance and StorageTool box located on belt cover Washer, Hvsptlk Nut, 1/2-13 Hexjam Spare SpacersAdjust Parts packed separately in carton not shown full sizeGlasses or eye shields while assembling snow thrower To Remove Snow Thrower from Carton To Install the Upper Handle and Crank AssemblyTo Install Shifter Lever Knob To Assemble Snow ChuteControl Cables Discharge Chute Changes the direction the snow is thrown HOW to SET UP Your Snow ThrowerKnow Your Snow Thrower To Throw Snow HOW to USE Your Snow Thrower To Stop ,OURSNOW ThrowerTo Control Snow Discharge To Move Forward BackwardFill OIL Fill GASBefore Starting the Engine Cold Start To Start Engine Electric StarterTo Stop Engine To Stop EngineFrozen Recoil Starter One time if temperature is above 50ECold Start Warm StartYou complete Jroduct Specifications Horse Power 5HPService Schedule Records Dates Customer ResponsibilitiesAfter First USE Lubrication ChartSnow Thrower Lubrication Every 25 Hours General RecommendationsLubrication Engine LubricationSpark Plug To Adjust Skid Height To Adjust the Clutch Control CablesTo Adjust Scraper BAR Auger Drive Belt Traction Drive BeltTo Replace Belts To Adjustthe Belt Guide To Adjustthe Friction WblEELDisconnect the spark plug wire To Replace Friction Wheel Protection provided by the shear bolt To Adjust CarburetorTo Adjust or Replace Spark Plug To AdjustSnow Thrower Storage Engine StorageWarm Cause TroubleDifficult starting Electric Start Assembly NO. Part no Engine Part NO. Part NamePart Name Frame Assembly Craftsman 22 5H.P. Snow ThrowerIref Partname NO. Part NO. Part Name Drive Assembly305 326 301 327 311 312 321304 310 303315 320 Craftsman 22 -5H.P.SNOW Thrower Gear Case Assembly34O 312 311Part Name NO. Part no Auger Housing AssemblyCraftsman 22 5H.P, Snow Thrower 5OO00 Cam Discharge Chute AssemblyCraftsman 22 5H.P. Snow Thrower 536.886141 Handle Assembly 744NO. Part no Part Name Wheel Assembly Shift Yoke Assembly Part NamePart Name NO, Part no Chute Control ROD Assembly NO. Part NO, Part NameDecals Carburetor 640084A PART#Throttle Crack Screw Craftsman 4-CYCLE Engine Model Number REF. PART# Part Name O20OSDOG, Starter PART# Part NameSTARTER, Rewind RetainerPart Name Electric Starter 110 Volt Retainer Ring Starter no E PART#¢ircumstancia Tabla de contenidosGarantia Servicio y AjustesOperacion PREPARAClONMantenimiento Y Almacenamiento Page Para Retirar LA Removedora Como Instalar SURemovedora DE Nieve Mecanismo Natural 3 de LOS Cables DE Control DEL Embrague Para Instalar LA Perilla DE LA Palanca DE CambiosPara Montar LA Removedora Para INSPECClONAR/AJUSTARConnozca SU Removedora DE Nieve Pot esfuerzo Nieve Illenoi y la marca agregar Como Usar EL Pasador DE EN Ganche DE LA RuedaAntes DE Encender EL Motor Antes DE Arrancar EL MotorArranque EN Frio Para Parar EL MotorNOTA,NO Rote LA Llave Para Arrancar EL Motor Arrancador elctricoArranque EN Caliente Para Encender EL MotorRetroceso Manual Si el arrancador estd congelado y no arranca el motor Arranque CongeladoDespues DE USA RLA POR Primera VEZ Caballos DE Fuerza 5CVDesplazamiento 12o04 pulg. cbicas Recomendaciones GeneralesLUBRICAClON Removedora DE NieveLUBRICAClON Cada 25 Horas Recomendacion DE Aceite Nota En condicionesde fro extremoMotor Lubricacion Lleno y la marca agregarPrecaucion Asegurese de Para Ajustar LA Altura DE LA Corredera DE ApoyoTuercas de montajede las correderas apoyo Para Ajustar LA Barra RaspadoraCorrea DE Propulsion DE LA Oruga Para Reemplazar CorreasCorrea Propulsora DE Para Ajustar LAS Correas Correa DE Propulsion DEL BarrenoPolea tensora OrugaAjuste DE LAS Guia DE LA Correa Poade transmision Guta de correaPara Reemplazar LA Rueda DE Friccion Cortante de equipo Para Ajustar EL CarburadorPara Ajustar O Reemplazar LA Bujia Para AjustarPara Reemplazar Otros Almacenamiento DE LA Removedora DE NieveAlamcenamiento DEL Motor Problema Causa CorreccionILa unidad no descarga nieve 800=827-6655