Craftsman 536.886141 manual Parts packed separately in carton not shown full size, Adjust

Page 5

1- Screw, 5/16-18 x 2 In.	3 - Carriage Bolts, 5116-18x1.00 In.

Parts packed separately in carton (not shown full size)

2- Ignition Keys

(Attached to engine in plastic bag)

1 - container 5W30 oil

I - Snow Chute Assembly

1 - Crank Assembly

CAUTION: Always wear safety

glasses or eye shields while assembling snow thrower.

TOOLS REQUIRED FOR ASSEMBLY

1 - Knife to cut carton and plastic ties

2 - 112 inch wrenches (or adjustable wrenches)

2 - 9/!6 inch wrenches (or adjustable wrenches)

2 - 3/4 inch wrenches (or adjustable wrenches)

1 - Pliers (to spread cotter pin)

1 - Measuring tape or ruler

The figure below shows the snow thrower in the shipping carton.

Lower handl

Clutch

The figure below shows the snow thrower completely assembled.

References to the right or left hand side

of the snow thrower are from the viewpoint of the operator'sposition behind the unit.

Auger driv_ lever	drive lever
	cable
	assembly
Shifter
lever

Upper handle

Height

adjust

skids

assembly

Image 5

Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower ServicePreparation TrainingOperation Tool box located on belt cover Maintenance and StorageWasher, Hvsptlk Nut, 1/2-13 Hexjam Spare Spacers Starter Motor Cord 10FtGlasses or eye shields while assembling snow thrower AdjustParts packed separately in carton not shown full size To Remove Snow Thrower from Carton To Install the Upper Handle and Crank AssemblyControl Cables To Install Shifter Lever KnobTo Assemble Snow Chute Discharge Chute Changes the direction the snow is thrown HOW to SET UP Your Snow ThrowerKnow Your Snow Thrower To Control Snow Discharge HOW to USE Your Snow Thrower To Stop ,OURSNOW ThrowerTo Move Forward Backward To Throw SnowBefore Starting the Engine Fill OILFill GAS To Stop Engine To Start Engine Electric StarterTo Stop Engine Cold StartCold Start One time if temperature is above 50EWarm Start Frozen Recoil StarterService Schedule Records Dates Jroduct Specifications Horse Power 5HPCustomer Responsibilities You completeSnow Thrower Lubrication Every 25 Hours Lubrication ChartGeneral Recommendations After First USESpark Plug LubricationEngine Lubrication To Adjust Scraper BAR To Adjust Skid HeightTo Adjust the Clutch Control Cables To Replace Belts Auger Drive BeltTraction Drive Belt Disconnect the spark plug wire To Adjustthe Belt GuideTo Adjustthe Friction WblEEL To Replace Friction Wheel To Adjust or Replace Spark Plug To Adjust CarburetorTo Adjust Protection provided by the shear boltWarm Snow Thrower StorageEngine Storage Difficult starting CauseTrouble Part Name Electric Start Assembly NO. Part no EnginePart NO. Part Name Iref Partname Frame AssemblyCraftsman 22 5H.P. Snow Thrower NO. Part NO. Part Name Drive Assembly34O Craftsman 22 -5H.P.SNOW Thrower Gear Case Assembly312 311 305 326 301 327 311 312 321304 310 303315 320Craftsman 22 5H.P, Snow Thrower Auger Housing Assembly5OO Part Name NO. Part no00 Cam Discharge Chute AssemblyNO. Part no Part Name Craftsman 22 5H.P. Snow Thrower 536.886141 Handle Assembly744 Part Name NO, Part no Wheel AssemblyShift Yoke Assembly Part Name Decals Chute Control ROD AssemblyNO. Part NO, Part Name Throttle Crack Screw Carburetor 640084APART# Craftsman 4-CYCLE Engine Model Number REF. PART# Part Name O20OSSTARTER, Rewind PART# Part NameRetainer DOG, StarterPart Name Electric Starter 110 Volt Retainer Ring Starter no E PART#Garantia Tabla de contenidosServicio y Ajustes ¢ircumstanciaOperacion PREPARAClONMantenimiento Y Almacenamiento Page Removedora DE Nieve Para Retirar LA RemovedoraComo Instalar SU Mecanismo Natural 3 de Para Montar LA Removedora Para Instalar LA Perilla DE LA Palanca DE CambiosPara INSPECClONAR/AJUSTAR LOS Cables DE Control DEL EmbragueConnozca SU Removedora DE Nieve Pot esfuerzo Nieve Antes DE Encender EL Motor Como Usar EL Pasador DE EN Ganche DE LA RuedaAntes DE Arrancar EL Motor Illenoi y la marca agregarNOTA,NO Rote LA Llave Para Parar EL MotorPara Arrancar EL Motor Arrancador elctrico Arranque EN FrioRetroceso Manual Arranque EN CalientePara Encender EL Motor Si el arrancador estd congelado y no arranca el motor Arranque CongeladoDesplazamiento 12o04 pulg. cbicas Caballos DE Fuerza 5CVRecomendaciones Generales Despues DE USA RLA POR Primera VEZLUBRICAClON Cada 25 Horas LUBRICAClONRemovedora DE Nieve Motor Lubricacion Nota En condicionesde fro extremoLleno y la marca agregar Recomendacion DE AceiteTuercas de montajede las correderas apoyo Para Ajustar LA Altura DE LA Corredera DE ApoyoPara Ajustar LA Barra Raspadora Precaucion Asegurese deCorrea Propulsora DE Para Reemplazar CorreasPara Ajustar LAS Correas Correa DE Propulsion DEL Barreno Correa DE Propulsion DE LA OrugaAjuste DE LAS Guia DE LA Correa OrugaPoade transmision Guta de correa Polea tensoraPara Reemplazar LA Rueda DE Friccion Cortante de equipo Para Ajustar EL CarburadorPara Reemplazar Para Ajustar O Reemplazar LA BujiaPara Ajustar Alamcenamiento DEL Motor OtrosAlmacenamiento DE LA Removedora DE Nieve ILa unidad no descarga nieve Problema CausaCorreccion 800=827-6655