Craftsman 536.886141 manual To Replace Friction Wheel

Page 20

= Position the shifter lever in first (1) forward gear.

o Note the position of the friction wheel on the disc drive plate. The right outer side of the disc drive plate should be 3" from the center of the friction wheel (See figure be-

low)

Wheel	_--	----Hex Shaft
	°i

Bearin

Plate

Fasteners

Fri_ Wheel

HulBearing Plate Bolts

.....Auger/

> 3" <

If adjustment is necessary:

°Loosen bolts in speed selector lever (see figure below)°

Speed

TO REPLACE FRICTION WHEEL

tf the snow thrower will not move forward, and the friction wheel is worn or damaged, you need to replace it as follows: (First allow the engine to cool).

oDrain the gasoline from the fuel tank.

oDrain the fuel in a container and reinstall the fuel line.

°Disconnect the spark plug wire.

oStand the snow thrower up on the auger housing end (seefirst figure, next column).

o Remove the bottom panel (see last figure on page 19).

°Remove the three (3) fasteners securing the friction wheel to the hub (see figure above).

• Remove the four bolts securing the bear- ing plates (both sides), (see figure above).

o Remove right side bearing plate. Leave hex shaft in odginal position.

°Remove friction wheel from hub. Slip fric- tion wheel off hex shaft towards right side. See figure below.

-Position new friction wheel onto hub. See figure below.

Friction Wheel

Shaft

Bolt

Nut

°Install bearing plates to original position. Ensure hex shaft is engaged with both

bearing plates.

°Secure bearing plates, using bolts re- moved earlier.

2O

Image 20

Contents Snow Thrower Service Limited TWO-YEAR Warranty on Craftsman Snow ThrowerPreparation TrainingOperation Maintenance and Storage Tool box located on belt coverWasher, Hvsptlk Nut, 1/2-13 Hexjam Spare Spacers Starter Motor Cord 10FtGlasses or eye shields while assembling snow thrower AdjustParts packed separately in carton not shown full size To Install the Upper Handle and Crank Assembly To Remove Snow Thrower from CartonControl Cables To Install Shifter Lever KnobTo Assemble Snow Chute HOW to SET UP Your Snow Thrower Discharge Chute Changes the direction the snow is thrownKnow Your Snow Thrower HOW to USE Your Snow Thrower To Stop ,OURSNOW Thrower To Control Snow DischargeTo Move Forward Backward To Throw SnowBefore Starting the Engine Fill OILFill GAS To Start Engine Electric Starter To Stop EngineTo Stop Engine Cold StartOne time if temperature is above 50E Cold StartWarm Start Frozen Recoil StarterJroduct Specifications Horse Power 5HP Service Schedule Records DatesCustomer Responsibilities You completeLubrication Chart Snow Thrower Lubrication Every 25 HoursGeneral Recommendations After First USESpark Plug LubricationEngine Lubrication To Adjust Scraper BAR To Adjust Skid HeightTo Adjust the Clutch Control Cables To Replace Belts Auger Drive BeltTraction Drive Belt Disconnect the spark plug wire To Adjustthe Belt GuideTo Adjustthe Friction WblEEL To Replace Friction Wheel To Adjust Carburetor To Adjust or Replace Spark PlugTo Adjust Protection provided by the shear boltWarm Snow Thrower StorageEngine Storage Difficult starting CauseTrouble Part Name Electric Start Assembly NO. Part no EnginePart NO. Part Name Iref Partname Frame AssemblyCraftsman 22 5H.P. Snow Thrower Drive Assembly NO. Part NO. Part NameCraftsman 22 -5H.P.SNOW Thrower Gear Case Assembly 34O312 311 305 326 301 327 311 312 321304 310 303315 320Auger Housing Assembly Craftsman 22 5H.P, Snow Thrower5OO Part Name NO. Part noDischarge Chute Assembly 00 CamNO. Part no Part Name Craftsman 22 5H.P. Snow Thrower 536.886141 Handle Assembly744 Part Name NO, Part no Wheel AssemblyShift Yoke Assembly Part Name Decals Chute Control ROD AssemblyNO. Part NO, Part Name Throttle Crack Screw Carburetor 640084APART# Craftsman 4-CYCLE Engine Model Number O20OS REF. PART# Part NamePART# Part Name STARTER, RewindRetainer DOG, StarterStarter no E PART# Part Name Electric Starter 110 Volt Retainer RingTabla de contenidos GarantiaServicio y Ajustes ¢ircumstanciaPREPARAClON OperacionMantenimiento Y Almacenamiento Page Removedora DE Nieve Para Retirar LA RemovedoraComo Instalar SU Mecanismo Natural 3 de Para Instalar LA Perilla DE LA Palanca DE Cambios Para Montar LA RemovedoraPara INSPECClONAR/AJUSTAR LOS Cables DE Control DEL EmbragueConnozca SU Removedora DE Nieve Pot esfuerzo Nieve Como Usar EL Pasador DE EN Ganche DE LA Rueda Antes DE Encender EL MotorAntes DE Arrancar EL Motor Illenoi y la marca agregarPara Parar EL Motor NOTA,NO Rote LA LlavePara Arrancar EL Motor Arrancador elctrico Arranque EN FrioRetroceso Manual Arranque EN CalientePara Encender EL Motor Arranque Congelado Si el arrancador estd congelado y no arranca el motorCaballos DE Fuerza 5CV Desplazamiento 12o04 pulg. cbicasRecomendaciones Generales Despues DE USA RLA POR Primera VEZLUBRICAClON Cada 25 Horas LUBRICAClONRemovedora DE Nieve Nota En condicionesde fro extremo Motor LubricacionLleno y la marca agregar Recomendacion DE AceitePara Ajustar LA Altura DE LA Corredera DE Apoyo Tuercas de montajede las correderas apoyoPara Ajustar LA Barra Raspadora Precaucion Asegurese dePara Reemplazar Correas Correa Propulsora DEPara Ajustar LAS Correas Correa DE Propulsion DEL Barreno Correa DE Propulsion DE LA OrugaOruga Ajuste DE LAS Guia DE LA CorreaPoade transmision Guta de correa Polea tensoraPara Reemplazar LA Rueda DE Friccion Para Ajustar EL Carburador Cortante de equipoPara Reemplazar Para Ajustar O Reemplazar LA BujiaPara Ajustar Alamcenamiento DEL Motor OtrosAlmacenamiento DE LA Removedora DE Nieve ILa unidad no descarga nieve Problema CausaCorreccion 800=827-6655