Craftsman 536.886141 manual To Adjust Skid Height, To Adjust the Clutch Control Cables

Page 17

CAUTION: Always disconnect the

spark plug wire and tie back away from the plug before making any adjustments or repairs.

TO ADJUST SKID HEIGHT

This snow thrower is equipped with two height adjustment skids, located on the out- side of the auger housing (see figure be- low). These skids elevate the front of the snow thrower°

Skid Mo Nuts

Housing

Height Adjust Skids

 

For normal hard surfaces, adjust the skids as follows:

o Check tire pressure (14 to 17 pounds). o Place the extra shear bolts supplied

(found in parts bag) under each end of the scraper bar near but not under the skid.

o Loosen the skid mounting nuts (see figure

above) and adjust the skids up to bring the front of the snow thrower down. Re-

tighten the mounting nuts.

o Loosen the carriage bolts and nuts secur- ing the scraper bar to the auger housing.

=Adjust the scraper bar to the proper posi- tion.

Tighten the carriage bolts and nuts, mak- ing sure that the scraper bar is parallel with the working surface.

°For extended operation, the scraper bar may be reversed, tf the scraper bar must be replaced due to wear, remove the car- riage bolts and nuts and install a new scraper bar.

CAUTION: Be certain to maintain proper ground clearance for your particular area to be cleared. Objects such as gravel, rocks or other debris, if struck by the impeller, may be thrown with sufficient force to cause personal injury, property damage or dam_ age to the snow thrower°

TO ADJUST THE CLUTCH CONTROL

CABLES

Periodic adjustment of the cables may be required due to normal stretch and wear on

the belts. To check for correct adjustment, the control lever must be in the full forward

position, resting on the plastic bumper. The control cables are correctly adjusted when the center of the "Z" fitting is in the center of the hole and there is no droop in the cable. See figure below.

Set the skid on the other side at the same height.

Auger Drive Leve

Control Lever must be In futl

For rocky or uneven surfaces, adjust the skids as follows:

Raise the front of the snow thrower by moving the skids down. This will help pre- vent rocks and other debris from being picked up and thrown by the auger,

forwardposition

ring

"Z" Fittingplastfc bumper) when checking

TO ADJUST SCRAPER BAR

After considerable use, the metal scraper bar will have a definite wear pattern. The scraper bar may have to be returned to its original lower setting to maintain the original performance level. To adjust:

,Position the snow thrower on a level sur- face.

Make sure both tires are equally inflated. Proper tire pressure is 14 to 17 PSI. See side of tire for maximum inflation_ Do not

exceed sidewall maximum pressure on tire.

LicBumper

tf adjustment is necessary:

°Remove fuel from tank, and stand blower on end.

°Disconnect the "Z" fitting from drive lever.

°Pull rubber boot off the top of the spring. Push the cable through the spring (see first figure on page 18) to expose the threaded portion of the cable.

17

Image 17
Contents Snow Thrower Limited TWO-YEAR Warranty on Craftsman Snow Thrower ServicePreparation TrainingOperation Tool box located on belt cover Maintenance and StorageWasher, Hvsptlk Nut, 1/2-13 Hexjam Spare Spacers Starter Motor Cord 10FtGlasses or eye shields while assembling snow thrower AdjustParts packed separately in carton not shown full size To Remove Snow Thrower from Carton To Install the Upper Handle and Crank AssemblyControl Cables To Install Shifter Lever KnobTo Assemble Snow Chute Discharge Chute Changes the direction the snow is thrown HOW to SET UP Your Snow ThrowerKnow Your Snow Thrower To Control Snow Discharge HOW to USE Your Snow Thrower To Stop ,OURSNOW ThrowerTo Move Forward Backward To Throw SnowBefore Starting the Engine Fill OILFill GAS To Stop Engine To Start Engine Electric StarterTo Stop Engine Cold StartCold Start One time if temperature is above 50EWarm Start Frozen Recoil StarterService Schedule Records Dates Jroduct Specifications Horse Power 5HPCustomer Responsibilities You completeSnow Thrower Lubrication Every 25 Hours Lubrication ChartGeneral Recommendations After First USESpark Plug LubricationEngine Lubrication To Adjust Scraper BAR To Adjust Skid HeightTo Adjust the Clutch Control Cables To Replace Belts Auger Drive BeltTraction Drive Belt Disconnect the spark plug wire To Adjustthe Belt GuideTo Adjustthe Friction WblEEL To Replace Friction Wheel To Adjust or Replace Spark Plug To Adjust CarburetorTo Adjust Protection provided by the shear boltWarm Snow Thrower StorageEngine Storage Difficult starting CauseTrouble Part Name Electric Start Assembly NO. Part no EnginePart NO. Part Name Iref Partname Frame AssemblyCraftsman 22 5H.P. Snow Thrower NO. Part NO. Part Name Drive Assembly34O Craftsman 22 -5H.P.SNOW Thrower Gear Case Assembly312 311 305 326 301 327 311 312 321304 310 303315 320Craftsman 22 5H.P, Snow Thrower Auger Housing Assembly5OO Part Name NO. Part no00 Cam Discharge Chute AssemblyNO. Part no Part Name Craftsman 22 5H.P. Snow Thrower 536.886141 Handle Assembly744 Part Name NO, Part no Wheel AssemblyShift Yoke Assembly Part Name Decals Chute Control ROD AssemblyNO. Part NO, Part Name Throttle Crack Screw Carburetor 640084APART# Craftsman 4-CYCLE Engine Model Number REF. PART# Part Name O20OSSTARTER, Rewind PART# Part NameRetainer DOG, StarterPart Name Electric Starter 110 Volt Retainer Ring Starter no E PART#Garantia Tabla de contenidosServicio y Ajustes ¢ircumstanciaOperacion PREPARAClONMantenimiento Y Almacenamiento Page Removedora DE Nieve Para Retirar LA RemovedoraComo Instalar SU Mecanismo Natural 3 de Para Montar LA Removedora Para Instalar LA Perilla DE LA Palanca DE CambiosPara INSPECClONAR/AJUSTAR LOS Cables DE Control DEL EmbragueConnozca SU Removedora DE Nieve Pot esfuerzo Nieve Antes DE Encender EL Motor Como Usar EL Pasador DE EN Ganche DE LA RuedaAntes DE Arrancar EL Motor Illenoi y la marca agregarNOTA,NO Rote LA Llave Para Parar EL MotorPara Arrancar EL Motor Arrancador elctrico Arranque EN FrioRetroceso Manual Arranque EN CalientePara Encender EL Motor Si el arrancador estd congelado y no arranca el motor Arranque CongeladoDesplazamiento 12o04 pulg. cbicas Caballos DE Fuerza 5CVRecomendaciones Generales Despues DE USA RLA POR Primera VEZLUBRICAClON Cada 25 Horas LUBRICAClONRemovedora DE Nieve Motor Lubricacion Nota En condicionesde fro extremoLleno y la marca agregar Recomendacion DE AceiteTuercas de montajede las correderas apoyo Para Ajustar LA Altura DE LA Corredera DE ApoyoPara Ajustar LA Barra Raspadora Precaucion Asegurese deCorrea Propulsora DE Para Reemplazar CorreasPara Ajustar LAS Correas Correa DE Propulsion DEL Barreno Correa DE Propulsion DE LA OrugaAjuste DE LAS Guia DE LA Correa OrugaPoade transmision Guta de correa Polea tensoraPara Reemplazar LA Rueda DE Friccion Cortante de equipo Para Ajustar EL CarburadorPara Reemplazar Para Ajustar O Reemplazar LA BujiaPara Ajustar Alamcenamiento DEL Motor OtrosAlmacenamiento DE LA Removedora DE Nieve ILa unidad no descarga nieve Problema CausaCorreccion 800=827-6655