Craftsman 536.886141 manual To Remove Snow Thrower from Carton

Page 6

TO REMOVE SNOW THROWER FROM CARTON

Locate and remove container of 5W30 oil.

°Locate all parts packed separately and remove from the carton.

NOTE: Place fuel stabilizer in a safe place until needed for storage.

o Remove and discard the packing material from around the snow thrower°

o Cut al! four corners of the carton from top to bottom and lay the panels flat.

Roll the snow thrower off the carton by

pulling on the lower handle. CAUTION: DO NOT back over cables.

° Remove the packing material from

handle assembly and all plastic material on unit.

o Cut ties securing the clutch control cables to the lower handle and lay cables back away from the motor frame.

TO INSTALL THE UPPER HANDLE AND CRANK ASSEMBLY

Cut tie holding shift rod to lower handle and move shifter to the first(l) forward

gear.

Loosen, but do not remove the screws, flatwashers, lockwashers and hex nuts in the upper holes of the lower handle. See

figure below.

,_ Upper handle

.._\ Loosen do not

/ omo o

_ 11/32 Flatwasher

5/16" hex Nut

._=_.._5/16 X 2"

NOTE: if the cables have become discon-

nected, reinstall spring as shown in figure below.

Traction

J

Auger drive

drive

3" _pring

 

spri_,,__

 

 

¢ 4"

 

uger ddve

Traction Jrive springlever

NOTE: Position cable through slot on shifter plate.

°Install hardware supplied in the parts bag (Screw, flatwasher, loclo,r_asher, and hex nut) into lower hole on right hand side of handles. Do not tighten until all bolts are in place. See first figure on this page.

°Locate crank assembly removed earlier and remove the 3/8" nylon Iocknut and flatwasher from the eye bolt assembly.

See figure below.

,Reinstall flatwasher and adapter. Install eye bolt through lower hole in the left

hand side of the handle. See figure be- low.

°Install the 3/8" flatwasher and the 3/8" ny- lon Iocknut on the eye bolt as shown in figure below_

Upper handle

/

Screw

3/8" nylon

5/16" Lockwasher

°Raise upper handle into operating posi- tion. Upper handle should be to the outside of the lower handle.

NOTE' Make sure the cables are not caught between the upper and lower handle.

NOTE: if the cables have become discon- nected from the clutch levers, reinstall the

cables as shown in figure below.

"Z" fitting

locknut

Eye Bolt

Flatwasher

Carefully remove cotter pin, clevis pin and universal joint pin from yoke end of crank rod assembly as shown in next fig- ure.

Place universal joint into end of worm gear lining up large holes. Insert universal joint pin (ensure opening in pin is in line with small openings in universal joint).

Image 6
Contents Snow Thrower Preparation ServiceLimited TWO-YEAR Warranty on Craftsman Snow Thrower TrainingOperation Washer, Hvsptlk Nut, 1/2-13 Hexjam Spare Spacers Maintenance and StorageTool box located on belt cover Starter Motor Cord 10FtAdjust Parts packed separately in carton not shown full sizeGlasses or eye shields while assembling snow thrower To Install the Upper Handle and Crank Assembly To Remove Snow Thrower from CartonTo Install Shifter Lever Knob To Assemble Snow ChuteControl Cables HOW to SET UP Your Snow Thrower Discharge Chute Changes the direction the snow is thrownKnow Your Snow Thrower To Move Forward Backward HOW to USE Your Snow Thrower To Stop ,OURSNOW ThrowerTo Control Snow Discharge To Throw SnowFill OIL Fill GASBefore Starting the Engine To Stop Engine To Start Engine Electric StarterTo Stop Engine Cold StartWarm Start One time if temperature is above 50ECold Start Frozen Recoil StarterCustomer Responsibilities Jroduct Specifications Horse Power 5HPService Schedule Records Dates You completeGeneral Recommendations Lubrication ChartSnow Thrower Lubrication Every 25 Hours After First USELubrication Engine LubricationSpark Plug To Adjust Skid Height To Adjust the Clutch Control CablesTo Adjust Scraper BAR Auger Drive Belt Traction Drive BeltTo Replace Belts To Adjustthe Belt Guide To Adjustthe Friction WblEELDisconnect the spark plug wire To Replace Friction Wheel To Adjust To Adjust CarburetorTo Adjust or Replace Spark Plug Protection provided by the shear boltSnow Thrower Storage Engine StorageWarm Cause TroubleDifficult starting Electric Start Assembly NO. Part no Engine Part NO. Part NamePart Name Frame Assembly Craftsman 22 5H.P. Snow ThrowerIref Partname Drive Assembly NO. Part NO. Part Name312 311 Craftsman 22 -5H.P.SNOW Thrower Gear Case Assembly34O 305 326 301 327 311 312 321304 310 303315 3205OO Auger Housing AssemblyCraftsman 22 5H.P, Snow Thrower Part Name NO. Part noDischarge Chute Assembly 00 CamCraftsman 22 5H.P. Snow Thrower 536.886141 Handle Assembly 744NO. Part no Part Name Wheel Assembly Shift Yoke Assembly Part NamePart Name NO, Part no Chute Control ROD Assembly NO. Part NO, Part NameDecals Carburetor 640084A PART#Throttle Crack Screw Craftsman 4-CYCLE Engine Model Number O20OS REF. PART# Part NameRetainer PART# Part NameSTARTER, Rewind DOG, StarterStarter no E PART# Part Name Electric Starter 110 Volt Retainer RingServicio y Ajustes Tabla de contenidosGarantia ¢ircumstanciaPREPARAClON OperacionMantenimiento Y Almacenamiento Page Para Retirar LA Removedora Como Instalar SURemovedora DE Nieve Mecanismo Natural 3 de Para INSPECClONAR/AJUSTAR Para Instalar LA Perilla DE LA Palanca DE CambiosPara Montar LA Removedora LOS Cables DE Control DEL EmbragueConnozca SU Removedora DE Nieve Pot esfuerzo Nieve Antes DE Arrancar EL Motor Como Usar EL Pasador DE EN Ganche DE LA RuedaAntes DE Encender EL Motor Illenoi y la marca agregarPara Arrancar EL Motor Arrancador elctrico Para Parar EL MotorNOTA,NO Rote LA Llave Arranque EN FrioArranque EN Caliente Para Encender EL MotorRetroceso Manual Arranque Congelado Si el arrancador estd congelado y no arranca el motorRecomendaciones Generales Caballos DE Fuerza 5CVDesplazamiento 12o04 pulg. cbicas Despues DE USA RLA POR Primera VEZLUBRICAClON Removedora DE NieveLUBRICAClON Cada 25 Horas Lleno y la marca agregar Nota En condicionesde fro extremoMotor Lubricacion Recomendacion DE AceitePara Ajustar LA Barra Raspadora Para Ajustar LA Altura DE LA Corredera DE ApoyoTuercas de montajede las correderas apoyo Precaucion Asegurese dePara Ajustar LAS Correas Correa DE Propulsion DEL Barreno Para Reemplazar CorreasCorrea Propulsora DE Correa DE Propulsion DE LA OrugaPoade transmision Guta de correa OrugaAjuste DE LAS Guia DE LA Correa Polea tensoraPara Reemplazar LA Rueda DE Friccion Para Ajustar EL Carburador Cortante de equipoPara Ajustar O Reemplazar LA Bujia Para AjustarPara Reemplazar Otros Almacenamiento DE LA Removedora DE NieveAlamcenamiento DEL Motor Problema Causa CorreccionILa unidad no descarga nieve 800=827-6655