Husqvarna ST261E To remove belt cover, Entfernen der riemenabdeckung, Desmontar el cubre correas

Page 50

 

B

C

A

To remove belt cover

1.Remove the two (2) screws (A) securing belt cover (B) to frame

(C).

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten se- curely.

Entfernen der riemenabdeckung

1.Entfernen Sie die zwei (2) Schrauben (A), mit denen die Riemena- beckung (B) am Rahmen (C) befestigt ist.

2.Entfernen Sie die Riemenabdeckung.

•Befestigen Sie die Riemenabdeckung erneut, indem Sie die Ab- deckung und die Schrauben wieder anbringen und die Schrauben fest anziehen.

Pour enlever le couvercle de la courroie

1.Enlevez les deux (2) vis (A) en fixant le couvercle de la courroie (B) au châssis (C).

2.Enlevez le couvercle de la courroie.

•Remplacez le couvercle de la courroie en installant le couvercle et serrez solidement.

Het verwijderen van de riemhuls

1.Verwijder de twee (2) schroeven (A) die de riemhuls (B) aan het frame (C) bevestigen.

2.Verwijder de riemhuls.

•Zet de riemhuls weer terug door de huls en de schroeven terug te plaatsen en draai stevig aan.

Desmontar el cubre correas

1.Desmontar los dos (2) tornillos (A) que sujetan el cubre correas (B) a la carcasa (C).

2.Desmontar el cubre correas.

•Sustituir el cubre correas colocando la cubierta y los tornillos y apretando firmemente.

Rimuovere il coperchio della cinghia

1.Togliere le due (2) viti (A) che fissano il coperchio della cinghia (B) all’intelaiatura (C).

2.Togliere il coperchio della cinghia.

•Rimettere coperchio e viti, stringendo bene.

2

1

 

3

 

L K

A D

 

 

 

 

B

J

 

H

 

 

 

M

E

 

 

 

 

F

2

 

1

To replace belts

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing (1) from the frame as- sembly (2), it is important that an assistant stand in the operating position and hold the snow thrower handles (3). Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY (A) - Remove bolt (B), flat washer (D) securing pulley to engine crankshaft. Remove outside (auger) pulley

(A) only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two bolts (F) and lock washers (G) holding auger housing (1) and frame (2) together.

WARNING: As the last bolt is removed, have your assistant care- fully lower the handles down to the ground.

6.REMOVE AUGER BELT (H) from around pulley (E).

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove traction drive belt (K) from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm (J) and rotate ratchet clockwise to relieve tension.

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents ST 261E Contents Indice Sichere Bedienung einer Schnee fräse Instructions BedienungWartung und Lagerung PréparationFormación FonctionnementEntretien et rangement PreparaciónInstructies FuncionamientoMantenimiento y Conservación VoorbereidingPreparazione Onderhoud en OpslagAddestramento FunzionamentoManutenzione e conservazione ST 261E Enlever la souffleuse de la caisse en carton Remove snow thrower from the cartonEntnehmen der Schneefräse aus dem Karton Sacar la máquina quitanieves del cartónZusammensetzen der Schneefräse How to set up your snow throwerComment installer votre souffleuse Como preparar su máquina quita- nievesMontar la biela del control de velocidad Het installeren van de staaf van de snelhe- idsregelingAbrir la empuñadura superior Het uitpakken van de bovenste hendelMontar la biela del mando de tracción Install traction drive control rodInstallation des fahrantriebssteuerhebels Montaggio della barra di regolazione della trazioneInstallez la tige de contrôle de la vis sans fin Install auger control rodInstallation des Steuerhebels für die einzugssch- necken Het installeren van de regelstang van de boorregelingInstall discharge chute / chute rotater head Het installeren van de afvoertrechter / rotorkopInstall chute deflector remote control Montar el mando a distancia del deflector del conductoVérifiez la pression des pneus Check tire pressureÜberprüfen des reifendrucks Controlar la presión de los neumáticosPage ANREIßSTARTERGRIFF Comment Utiliser Votre Souffleuse HOW to USE Your Snow ThrowerBedienung DER SCHNEE- Fräse Como Utilizar SU Máquina QUIT- AnievesBenutzung des benzin-absperrventils F Pour utiliser la commande des gaz CTo use fuel shut-off valve F Pour utiliser le carburant fermez le robinet FBedienung des choke E Pour utiliser la commande d’étrangleur ETo use choke control E Usar el mando del cebador EPour contrôler la décharge de la neige To control snow dischargeRegelung des schneeauswurfs Regolare la bocca di scarico della neve Controlar la eyección de la nieveHet bedienen van de sneeuwuitstoot Das schneefräsen Using the clean-out toolTo throw snow Pour lancer de la neigeDe ontstopper gebruiken Utilisation de l’outil de nettoyageUsar la herramienta para la limpieza Utilizzo dello strumento di pulituraPour se déplacer vers l’avant et vers l’arrière To move forward and backwardVorwärts und rückwärts fahren Per spostarsi in avanti o all’indietro Moverse adelante y atrásVoorwaarts en achterwaarts bewegen Einstellen der gleitkufen N To adjust skid plates NScraper bar P Schaber PHet afstellen van de remplaten N Regular las placas de deslizamiento NBarra de arrastre P Schraperstang PVOR DEM Motorstart R FBefore Starting the Engine Avant DE Mettre LE Moteur EN MarchePrima DI Riavviare IL Motore Antes DE Poner EN Marcha EL MotorVoordat U DE Motor Start If recoil starter has frozen To start engineBefore stopping Motor anlassenPour mettre le moteur en marche Vor dem ausschaltenWenn der anreißstarter eingefroren ist Avant l’arrêtSi el arrancador de retroceso se ha congelado Puesta en marcha del motorAntes de parar De motor startenAvviare il motore Voordat u stoptAls de terugloopstarter is bevroren Conseils Pour LE Soufflage DE LA Neige Snow Throwing TipsHinweise FÜR DAS Schneefräsen Prima dell’arrestoConsigli PER Spazzare LA Neve Consejos Para Lanzar LA NieveTips Voor HET Sneeuwruimen Percorsi successivi e movendosi lentamenteService aantekeningen Service RecordSchema dentretien WartungsnachweisDati di servizio Tandwielcarter van de boor Sistema de tracciónRiemen Aandrijfsysteem met trekkabelEngine MotorMoteur Motore Limpieza CleaningReinigung SchoonmaakSneeuwruimer SouffleuseMáquina Quitanieves SpazzaneveShear bolts ScherbolzenVis de cisaillement Pernos de seguridadSchuifbouten Perni di sicurezzaPour enlever le couvercle de la courroie To remove belt coverEntfernen der riemenabdeckung Het verwijderen van de riemhulsInstall Belt Cover and two 2 screws. Tighten securely Erneuern der riemenBringen SIE DIE Riemenscheibe Wieder AN Pour remplacer les courroiesSustituir las correas Het vervangen van de riemen Sostituire le cinghie Pour enlever les roues To remove wheelsEntfernen der räder Desmontar las ruedasDe kabelspanning instellen To adjust cable tensionAjustement de la tension du câble Per regolare la tensione del cavoVergaser CarburetorEngine speed MotorgeschwindigkeitLagerung StorageOther SonstigesDivers EntreposageSouffleuse AlmacenajeImmagazzinaggio OpslagOverig AltroTroubleshooting StörungssucheSolución de problemas Recherche des causes d’une panneProbleemoplosser HET Probleem DE Oorzaak DE Oplossing532 42 93-55 07.07.09 TH

ST261E specifications

The Husqvarna ST261E is a powerful and versatile snow blower designed to tackle tough winter conditions with ease. This machine combines advanced technology with user-friendly features to deliver reliable performance, making it a favorite among homeowners and professionals alike.

One of the standout features of the ST261E is its robust 208cc engine. This powerful motor ensures high efficiency and reliable starting, even in cold weather. The electronic ignition system provides quick and easy starts without the hassle of priming or choking, making it perfect for those unexpected snowfalls.

The snow blower is equipped with a large 26-inch clearing width and a 23-inch intake height, allowing it to handle substantial amounts of snow in less time. Whether dealing with light flurries or heavy, wet snow, the ST261E is designed to clear paths quickly and efficiently. The adjustable skid shoes allow users to set the machine to different surfaces, ensuring optimal performance on driveways, sidewalks, and more.

One of the key innovations in the ST261E is its unique auger design. The heavy-duty auger is specially engineered to break up and throw snow with minimal effort, providing excellent throwing distance and reducing the risk of clogging. This feature is particularly useful when dealing with heavy, packed snow or icy conditions.

Furthermore, the snow blower includes a remote-controlled chute rotation, allowing operators to easily adjust the direction of snow discharge while on the move. This feature enhances maneuverability, enabling the user to effectively direct the snow where it needs to go without stopping the machine.

Comfort and ergonomics have not been overlooked in the design of the Husqvarna ST261E. The snow blower is equipped with an adjustable handle, allowing for optimal height adjustment to reduce fatigue during use. Additionally, the control panel is intuitively laid out, providing easy access to controls even while wearing gloves.

In conclusion, the Husqvarna ST261E is an outstanding option for those looking to conquer winter’s challenges. With its combination of power, innovative design, and user-friendly features, it ensures efficient snow removal, making it a reliable companion in the harshest of winter conditions. Whether for residential or light commercial use, the ST261E is engineered to deliver exceptional performance season after season.
Top Page Image Contents