To Move Forward and Backward See Fig | Husqvarna 927SB, 96193004400

	OPERATION
	HIGH	DISCHARGE CHUTE
	POSITION	DISCHARGE CHUTE
	POSITION
		CLEAN-OUT
		TOOL
	KNOB	MOUNTING
		CLIP
	CHUTE
	DEFLECTOR
	LOW POSITION	FIG. 15
		FIG. 15

		TO MOVE FORWARD AND BACKWARD (See Fig. 16)
	FIG. 13	TO MOVE FORWARD AND BACKWARD (See Fig. 16)
	FIG. 13	SELF-PROPELLING, forward and reverse movement of
	TO THROW SNOW (See Fig. 14)	SELF-PROPELLING, forward and reverse movement of
	The auger rotation is controlled by the auger control lever	the snow thrower, is controlled by the traction drive control
	The auger rotation is controlled by the auger control lever	lever located on the left side handle.
	located on the right side handle.	lever located on the left side handle.
	located on the right side handle.	• Squeeze traction drive control lever to handle to engage
	• Squeeze auger control lever to handle to engage the	• Squeeze traction drive control lever to handle to engage
	• Squeeze auger control lever to handle to engage the	the drive system.
	auger and throw snow.	the drive system.
	auger and throw snow.	• Release traction drive control lever to stop the forward
	• Release the auger control lever to stop throwing snow.	• Release traction drive control lever to stop the forward
	• Release the auger control lever to stop throwing snow.	or reverse movement of the snow thrower.
		or reverse movement of the snow thrower.
	AUGER	SPEED and DIRECTION are controlled by the drive speed
	AUGER	control lever.
	CONTROL	control lever.
	LEVER	• Press downward on the speed control lever and move
		lever to desired position BEFORE engaging the trac-
		tion drive control lever. Be sure lever springs back and
		locks into desired position.

			CAUTION: Do not move speed control lever
			when traction drive control lever is engaged.
	FIG. 14		when traction drive control lever is engaged.
	FIG. 14		Damage to the snow thrower can result.
	USING THE CLEAN-OUT TOOL (See Fig. 15)
	USING THE CLEAN-OUT TOOL (See Fig. 15)		• Slower speeds are for heavier snow and faster speeds
	In certain snow conditions, the discharge chute may be-		• Slower speeds are for heavier snow and faster speeds
	In certain snow conditions, the discharge chute may be-		are for light snow and transporting the snow thrower. It
	come clogged with ice and snow. Use the clean-out tool		are for light snow and transporting the snow thrower. It
	come clogged with ice and snow. Use the clean-out tool		is recommended that you use a slower speed until you
	to dislodge this blockage.		is recommended that you use a slower speed until you
	to dislodge this blockage.		are familiar with the operation of the snow thrower.
			are familiar with the operation of the snow thrower.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe di- rection (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 16

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous-

ing and the discharge chute.	10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 16)

TO THROW SNOW (See Fig. 14)

when traction drive control lever is engaged.

Damage to the snow thrower can result.

USING THE CLEAN-OUT TOOL (See Fig. 15)

•Release the auger control lever and shut off the engine.