Husqvarna 927SB, 96193004400 owner manual BAG of Parts, Power Cord, Retainer PIN, Wrench

Page 38

REPAIR PARTS

BAG OF PARTS

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

3

4

5

KEY

PART

 

 

 

 

NO.

NO.

DESCRIPTION

 

 

 

1

532 19 85-63

POWER CORD

2

1

8

2

532 16 96-75

RETAINER PIN

 

7

3

532 18 06-84

WRENCH

 

 

 

 

 

4

873 80 06-00

LOCKNUT 3/8−16

 

 

6 01.14.004-A

5

819 13 13-16

WASHER 3/8

 

 

 

6

532 19 86-36 SHEAR BOLT 1/4−20 X 1−3/4

 

 

 

7

532 19 86-38

SPACER

 

 

 

8

873 80 04-00 LOCKNUT 1/4−20

 

 

 

1

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 03 50-62 SAFETY IGNITION KEY

01.14.008-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigPrimer OperationKnow Your Snow Thrower Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Engine Speed StorageCarburetor Fuel SystemOther CylinderTroubleshooting Scraper BAR Auger Housing / Impeller AssemblyKEY Part Description Auger BearingAuger 27 LH Auger 27 RHExploded Bearing 532 19 67-10 Gearbox AssemblyImpeller Tool ClipStrap Repair Parts532 18 41-13 Deflector Weldment Knob BlackControl Panel / Discharge Chute Bulb Handles532 42 14-48 Headlight Bezel Gray Lower Tube01.08.004-B Knob RED SpacerRetainer Handle KnobClutch ROD 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Rear PlateDrive HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Pinion Gear3534 532 19 84-74 Speed Selector Head Assembly 532 18 40-74 Idler Pivot BracketAssembly 532 17 93-54 Idler Traction ARM Idler PulleyGear Axle ShaftRoll PIN 3/16 Clik PIN Bottom PAN ENGINE, TEC Frame Impeller Belt Chassis / Engine / PulleysPulley Wheel Assembly LH WheelsBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement
Top Page Image Contents