Husqvarna 927SB, 96193004400 Auger Housing / Impeller Assembly, KEY Part Description, Scraper BAR

Page 20

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

1

3 (5x)

4 (5x)

2

01.07.002-A

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 40 77-99 AUGER HOUSING 27

2

532 40 77-27

SCRAPER BAR

3

872 27 05-05 CARRIAGE BOLT 5/16−18 X .625

4

532 15 53-77

NUT 5/16−18

2

3

 

1

1

2

 

 

KEY

PART

 

 

 

NO.

NO.

 

DESCRIPTION

 

 

1

532

42 04-78

AUGER BEARING

3

 

2

532

41 19-39

BEARING PLUG

 

01.07.024-B

3

532

17 95-82

SCREW 5/16−18 X 1.00

 

 

 

 

 

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigOperation Know Your Snow ThrowerPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingWhen traction drive control lever is engaged Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Throw Snow See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Carburetor Engine Speed Fuel SystemOther CylinderTroubleshooting Auger Housing / Impeller Assembly KEY Part DescriptionScraper BAR Auger BearingAuger 27 LH Auger 27 RHExploded 532 19 67-10 Gearbox Assembly ImpellerBearing Tool ClipRepair Parts 532 18 41-13 Deflector WeldmentStrap Knob BlackControl Panel / Discharge Chute Handles 532 42 14-48 Headlight Bezel GrayBulb Lower Tube01.08.004-B Spacer RetainerKnob RED Handle Knob532 18 04-80 Impeller ROD Assembly 532 40 57-40 Traction ROD AssemblyClutch ROD Rear PlateDrive 532 17 53-44 Trunnion Bearing Assembly Control Shaft AssemblyHEX Shaft Pinion Gear3534 Assembly 532 18 40-74 Idler Pivot Bracket Assembly 532 17 93-54 Idler Traction ARM532 19 84-74 Speed Selector Head Idler PulleyAxle Shaft Roll PIN 3/16Gear Clik PINBottom PAN ENGINE, TECFrame Impeller Belt Chassis / Engine / PulleysPulley Wheel Assembly LH WheelsPower Cord KEY Part Description 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement
Top Page Image Contents