Husqvarna 927SB, 96193004400 owner manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotate chute assembly to alignsquare andpin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATOR		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATOR HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

Image 6

Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigPrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDrive speed control lever used to select forward or HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Engine Speed StorageCarburetor Fuel SystemOther CylinderTroubleshooting Scraper BAR Auger Housing / Impeller AssemblyKEY Part Description Auger BearingAuger 27 LH Auger 27 RHExploded Bearing 532 19 67-10 Gearbox AssemblyImpeller Tool ClipStrap Repair Parts532 18 41-13 Deflector Weldment Knob BlackControl Panel / Discharge Chute Bulb Handles532 42 14-48 Headlight Bezel Gray Lower Tube01.08.004-B Knob RED SpacerRetainer Handle KnobClutch ROD 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Rear PlateDrive HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Pinion Gear3534 532 19 84-74 Speed Selector Head Assembly 532 18 40-74 Idler Pivot BracketAssembly 532 17 93-54 Idler Traction ARM Idler PulleyGear Axle ShaftRoll PIN 3/16 Clik PINENGINE, TEC FrameBottom PAN Chassis / Engine / Pulleys PulleyImpeller Belt Wheel Assembly LH WheelsBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement