Husqvarna 96193004400 532 17 53-44 Trunnion Bearing Assembly, HEX Shaft, Pinion Gear, Clevis PIN

Page 31

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

KEY	PART
NO.	NO.	DESCRIPTION
1	817 49 05-08 BOLT 5/16−18 X .500
2	532 75 11-53	NUT 5/16−18
3	532 18 00-17 FLANGE BEARING
4	873 93 05-00	NUT 5/16−18

5532 19 95-09 RUBBER WHEEL PLATE

6532 17 98-31 RUBBER WHEEL RING

7532 17 86-13 RUBBER WHEEL HUB

8874 76 05-14 BOLT 5/16−18 X .875

9532 17 53-44 TRUNNION BEARING ASSEMBLY

10	812 00 00-12	RETAINER
11	532 18 00-66	HEX SHAFT
12	532 18 00-65	PINION GEAR

13532 19 29-07 AUXILIARY PLATE

14532 17 92-70 SPACER PLATE

15532 18 00-82 INTERMEDIATE GEAR

16532 18 01-34 AUXILIARY SHAFT

17532 40 54-85 CONTROL ARM

18	532 05 70-79	WASHER
19	532 40 61-09	CONTROL SHAFT ASSEMBLY
20	532 19 85-80	CLEVIS PIN

21532 18 40-80 SHIFTER LEVER

22532 18 78-57 PIVOT BRACKET

23	532 17 88-07	PIVOT PIN
24	532 18 01-35	SPRING
25	532 18 71-01	SHIFTER LINK
26	532 08 51-79	RETAINER
27	532 70 02-79	CLIP
28	532 15 00-78 BOLT 5/16−18 x .750

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 31

Image 31

Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDrive speed control lever used to select forward or Stopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Fuel System StorageCarburetor Engine SpeedCylinder OtherTroubleshooting Auger Bearing Auger Housing / Impeller AssemblyKEY Part Description Scraper BARAuger 27 RH Auger 27 LHExploded Tool Clip 532 19 67-10 Gearbox AssemblyImpeller BearingKnob Black Repair Parts532 18 41-13 Deflector Weldment StrapControl Panel / Discharge Chute Lower Tube Handles532 42 14-48 Headlight Bezel Gray Bulb01.08.004-B Handle Knob Spacer Retainer Knob REDRear Plate 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Clutch RODDrive Pinion Gear 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly HEX Shaft3534 Idler Pulley Assembly 532 18 40-74 Idler Pivot BracketAssembly 532 17 93-54 Idler Traction ARM 532 19 84-74 Speed Selector HeadClik PIN Axle ShaftRoll PIN 3/16 GearFrame ENGINE, TECBottom PAN Pulley Chassis / Engine / PulleysImpeller Belt Wheels Wheel Assembly LHRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement