Husqvarna 96193004400, 927SB owner manual Engine, Tec, Frame, Bottom PAN

Page 35

REPAIR PARTSCHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

1	3

201.00.018-A

KEY	PART
NO.	NO.	DESCRIPTION
-	- - - - - -	ENGINE, TEC
		MODEL LH318SA-156551H
1	532 41 61-55	FRAME
2	532 41 08-77	BOTTOM PAN
3	532 15 04-06	BOLT 3/8−16
4	532 18 44-71 SCREW 10−24 X .625

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 35

Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Fuel System StorageCarburetor Engine SpeedCylinder OtherTroubleshooting Auger Bearing Auger Housing / Impeller AssemblyKEY Part Description Scraper BARAuger 27 RH Auger 27 LHExploded Tool Clip 532 19 67-10 Gearbox AssemblyImpeller BearingKnob Black Repair Parts532 18 41-13 Deflector Weldment StrapControl Panel / Discharge Chute Lower Tube Handles532 42 14-48 Headlight Bezel Gray Bulb01.08.004-B Handle Knob SpacerRetainer Knob REDRear Plate 532 18 04-80 Impeller ROD Assembly532 40 57-40 Traction ROD Assembly Clutch RODDrive Pinion Gear 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly HEX Shaft3534 Idler Pulley Assembly 532 18 40-74 Idler Pivot BracketAssembly 532 17 93-54 Idler Traction ARM 532 19 84-74 Speed Selector HeadClik PIN Axle ShaftRoll PIN 3/16 GearBottom PAN ENGINE, TECFrame Impeller Belt Chassis / Engine / PulleysPulley Wheels Wheel Assembly LHRetainer PIN Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement

REPAIR PARTSCHASSIS / ENGINE / PULLEYS

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

KEY

ENGINE, TEC

FRAME

BOTTOM PAN