Husqvarna 96193004400, 927SB owner manual Auger 27 LH, Auger 27 RH

Page 21

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 927SB (96193004400), PRODUCT NO. 961 93 00-44

2

1

	KEY	PART
	NO.	NO.	DESCRIPTION
01.07.018-A	1	532 42 11-35	AUGER 27 LH
	1	532 42 11-35	AUGER 27 LH
	2	532 42 11-23	AUGER 27 RH

3

			4
				2
		4
		KEY	PART
		NO.	NO.	DESCRIPTION
		1	532 18 40-93 SKID PLATE LH
		2	532 18 40-94 SKID PLATE RH
		3	872 27 05-06 CARRIAGE BOLT 5/16−18 X .75
		4	532 75 11-53	NUT 5/16−18
3	01.11.001-A	1
3		1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21

Image 21

Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDrive speed control lever used to select forward or Stopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig When traction drive control lever is engagedTo Move Forward and Backward See Fig To Throw Snow See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Carburetor StorageEngine Speed Fuel SystemCylinder OtherTroubleshooting KEY Part Description Auger Housing / Impeller AssemblyScraper BAR Auger BearingAuger 27 RH Auger 27 LHExploded Impeller 532 19 67-10 Gearbox AssemblyBearing Tool Clip532 18 41-13 Deflector Weldment Repair PartsStrap Knob BlackControl Panel / Discharge Chute 532 42 14-48 Headlight Bezel Gray HandlesBulb Lower Tube01.08.004-B Retainer SpacerKnob RED Handle Knob532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD AssemblyClutch ROD Rear PlateDrive Control Shaft Assembly 532 17 53-44 Trunnion Bearing AssemblyHEX Shaft Pinion Gear3534 Assembly 532 17 93-54 Idler Traction ARM Assembly 532 18 40-74 Idler Pivot Bracket532 19 84-74 Speed Selector Head Idler PulleyRoll PIN 3/16 Axle ShaftGear Clik PINENGINE, TEC FrameBottom PAN Chassis / Engine / Pulleys PulleyImpeller Belt Wheels Wheel Assembly LHKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement