Husqvarna 96193004400, 927SB owner manual Unfold Upper Handle, Install Speed Control ROD See Figs

Page 5

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD
	RETAINER
	SPRING
SPEED	SPEED
CONTROL	CONTROL
BRACKET	LEVER

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

FIG. 2

5

Image 5

Contents 927SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig When traction drive control lever is engagedTo Move Forward and Backward See Fig To Throw Snow See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Carburetor StorageEngine Speed Fuel SystemCylinder OtherTroubleshooting KEY Part Description Auger Housing / Impeller AssemblyScraper BAR Auger BearingAuger 27 RH Auger 27 LHExploded Impeller 532 19 67-10 Gearbox AssemblyBearing Tool Clip532 18 41-13 Deflector Weldment Repair PartsStrap Knob BlackControl Panel / Discharge Chute 532 42 14-48 Headlight Bezel Gray HandlesBulb Lower Tube01.08.004-B Retainer SpacerKnob RED Handle Knob532 40 57-40 Traction ROD Assembly 532 18 04-80 Impeller ROD AssemblyClutch ROD Rear PlateDrive Control Shaft Assembly 532 17 53-44 Trunnion Bearing AssemblyHEX Shaft Pinion Gear3534 Assembly 532 17 93-54 Idler Traction ARM Assembly 532 18 40-74 Idler Pivot Bracket532 19 84-74 Speed Selector Head Idler PulleyRoll PIN 3/16 Axle ShaftGear Clik PINBottom PAN ENGINE, TECFrame Impeller Belt Chassis / Engine / PulleysPulley Wheels Wheel Assembly LHKEY Part Description 532 03 50-62 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement