Sanyo Projector owner manual Connecting to the LAN line

Page 12

Chapter 2 Setup Procedures

Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately.

Connecting to the LAN line

Connect the LAN cable to the LAN connection terminal of the projector.

LAN Connection Terminal

ACT Lamp (Orange) Blink orange when the projector is sending or receiving the data.

LINK Lamp (Green) Light green when the projector is connected to the network correctly.

LAN Cable

* Please use a shielded LAN cable.

Network configuration

Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “3. Basic setting and operation” (p.17-30). First, complete the settings described in this chapter before performing steps in “3. Basic setting and opera- tion.”

Setting Procedure

1.Select “Network” in the Network menu, and press Point 8 or SELECT button.

2.Select "On" with the Point ed buttons, and the press SELECT button. Then the Menu will disappear, the “Please wait...” message will appear, and switching operation will start. Switching will take a while and the projector’s LINK/ACT Lamp will be on or blink, and after completing the operation, the “Please wait...” message will disappear.

12

Image 12

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Features Internet IntranetNetwork specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN code169.254.100.100 255.255.0.0255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Sets Dhcp configuration ON/OFFMail setting Setting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Check / DeleteSetting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next PJ statusAbout projector condition Status DescriptionControl InputMeet the input signal are listed SystemItem Description Image adjustment Image mode Video ComputerPC adjustment Setting up the projector Screen settingLens adjustment Screen mode VideoInput source Normal Full Wide169 Zoom True Natural wide CustomSetting Resets the settings of Picture in Picture Stores the adjustment values. Select aMode no. User1 User5 from the pull Clear the adjustment values. SelectDefault, OFF Remote controlSets on or off the logo display on Shutter management...Sets the shutter management operationSets the color of the contents. Color Time, Network PIN code, Network settingSettings, etc Sets the digital processingInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Chapter Appendix Examples of connection Peer-To-Peer connectionGateway Router installed in the network To another networkUse of telnet ControlUse the IP address assigned to the projector Password 1234 is used for the example Command FunctionC00 Power on C01 Power off C05 Input C06 C07 C08 Menu display onWeb browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? OperationWhat is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KL8A