Sanyo Projector owner manual Network configuration, Sets Dhcp configuration ON/OFF

Page 24

Chapter 3 Basic Setting and Operation

Network configuration

Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this menu.

The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds.

	* The numerical value is a setting example.
Item	Description

DHCP	Sets DHCP configuration (ON/OFF).
IP address	Sets IP address of the projector
Subnet mask	Sets Subnet mask. Normally sets 255.255.255.0
Default gateway*1	Sets IP address of the default gateway (Router)
DNS*2	Sets IP address of the DNS server. Must be set when using the e-mail function

Projector name*3.Sets name of the projector. (64 characters maximum)

✐You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [192.168.001.101].

*1 Set [0.0.0.0] if the network does not provide the gateway (router).

*2 Set [0.0.0.0] if you do not use the function E-Mail alert.

*3 If you use the DNS server, register the host name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector.

*All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.

*If you make incorrect settings, you cannot find out the new network settings. Be careful to set up

24

them correctly, otherwise you cannot connect to the projector. It is recommended to make a note of them.

Image 24

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Features Internet IntranetNetwork specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN code169.254.100.100 255.255.0.0255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Sets Dhcp configuration ON/OFFMail setting Setting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Check / DeleteSetting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next PJ statusAbout projector condition Status DescriptionControl InputMeet the input signal are listed SystemItem Description Image adjustment Image mode Video ComputerPC adjustment Setting up the projector Screen settingLens adjustment Screen mode VideoInput source Normal Full Wide169 Zoom True Natural wide CustomSetting Resets the settings of Picture in Picture Stores the adjustment values. Select aMode no. User1 User5 from the pull Clear the adjustment values. SelectDefault, OFF Remote controlSets on or off the logo display on Shutter management...Sets the shutter management operationSets the color of the contents. Color Time, Network PIN code, Network settingSettings, etc Sets the digital processingInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Chapter Appendix Examples of connection Peer-To-Peer connectionGateway Router installed in the network To another networkUse of telnet ControlUse the IP address assigned to the projector Password 1234 is used for the example Command FunctionC00 Power on C01 Power off C05 Input C06 C07 C08 Menu display onWeb browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? OperationWhat is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KL8A