Sanyo Projector owner manual Examples Type and contents of alert mail

Page 28

Chapter 3 Basic Setting and Operation

Examples: Type and contents of alert mail

When the projector has an abnormality, the following alert messages are sent to the regis- tered E-mail address according to your selected condition. Administrator or user can take an efficient action quickly by receiving this message. This is very useful to maintain and service the projector.

The following are examples of received messages.

●When internal PJ temperature is too high:

TITLE: Message from projector

 

Projector Model Name: model name

 

TCP/IP: 192.168.1.201 Projector Name: Proj05

E-mail Header

 

It sends you following message.

*The projector lamp is turned off, because internal temperature goes over the safety limit. Wait for the completion of the cooling process and make sure the projector has been turned into Standby. Then turn the projector on again.

If the Indicator continues flashing, check the air filter for dust accumulation.

●When PJ needs service:

*Maintenance requirement from Projector is detected.

Check up LED status of projector and consult with the dealer.

AD,

3.3V

OK

 

KS,

3.3V

OK

 

---

---

---

 

MAIN,

3.3V

NG

Error information

---

---

---

 

✐The projector lamp was turned off, because the projector power circuit failed.

Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information.

●When PJ lamp replacement time is reached:

*The projector lamp 1 has reached replacement time. Lamp 1 ON 2000 h

Lamp 2 ON 1800 h

✐Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power- on of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached".

●When the brightness (Current value) continuously goes down a certain rate from Target value in Constant mode:

*The brightness (Current value) continuously goes down a certain rate from the value in Constant mode. Check the lamp status and replace the lamp, or decrease Target value in Constant mode.

✐This alert mail will be sent when "Lamp mode" is set to "Constant mode".

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Features Internet IntranetNetwork specifications of the projector Required operating environment for computersUse of this manual Expression/AbbreviationTrademarks Connect the LAN and set the configuration Flow of installationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN code255.255.0.0 169.254.100.100255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login Login the setting page of the projectorEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Sets Dhcp configuration ON/OFFMail setting Setting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Check / DeleteSetting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalTrap check/delete Up to 99,999 hours can be set for the time settingClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next PJ statusAbout projector condition Status DescriptionControl InputSystem Meet the input signal are listedItem Description Image adjustment Image mode Video ComputerPC adjustment Setting up the projector Screen settingLens adjustment Screen mode VideoInput source Normal Full Wide169 Zoom True Natural wide CustomSetting Resets the settings of Picture in Picture Stores the adjustment values. Select aMode no. User1 User5 from the pull Clear the adjustment values. SelectDefault, OFF Remote controlSets on or off the logo display on Shutter management...Sets the shutter management operationSets the color of the contents. Color Time, Network PIN code, Network settingSettings, etc Sets the digital processingInformation InformationItems Description Network Indication of the filter status Indication of the lamp statusStatus Chapter Appendix Examples of connection Peer-To-Peer connectionGateway Router installed in the network To another networkControl Use of telnetUse the IP address assigned to the projector Password 1234 is used for the example Command FunctionC00 Power on C01 Power off C05 Input C06 C07 C08 Menu display onActive Script/JavaScript enable Web browser settingProxy setting Windows XP Professional Examples OS/BrowsersInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? OperationWhat is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KL8A
Top Page Image Contents