Sanyo Projector owner manual Image adjustment, Image mode Video Computer

Page 36

Chapter 4 Controlling the Projector

Image adjustment

This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button.

Item	Description
Contrast		Adjusts picture contrast.
Brightness		(0~ 63)
Brightness		Adjusts picture brightness.
Color		(0~ 63)
Color		Adjusts picture color satura-
Tint		tion. (0~ 63)
Tint		Adjusts picture hue. (0~ 63)
Color temp		Sets a color temperature
		mode. (X Low, Low, Mid, High,
White balance		Adj.)
White balance
Red, Green, Blue		Adjusts each white balance
		respectively. (0~ 63)

*When changing the value of the white balance, the color temp. indicates "Adj."

Offset

Red, Green, Blue	Adjusts each offset respec-
Auto picture control	tively. (0~ 63)
Auto picture control	Sets auto picture control
Advanced color	level. (OFF, L1, L2)
Advanced color	Applies improved color
	adjustment with yellow
Sharpness	light controller. (Auto, OFF)
Sharpness	Adjusts picture sharpness.
Gamma	(0~ 31)
Gamma	Adjusts brightness of darker
Noise reduction	part of the picture. (0~ 15)
Noise reduction	Switches noise reduction mode (ON, OFF)
Progressive	Switches progressive mode (OFF, ON, Film)
Reset	Resets the Image adjustment to previous levels.
Store	Stores the Image adjustment values. Select an item [Image1 - Image10] from
	the pull-down menu and click Store button.

Load Image mode...........Loads the Image mode. Select an image mode from the pull-down menu

and click Load button. There may not be available mode depending on the input mode as shown in the table left.

36

Input source

Image mode Video Computer

Standard	4	4
Cinema	4	*
Real	*	4
Dynamic	4	4
Image1 - 10	4	4

*When Edge blending is set to "ON", Auto picture control and Advanced color are disable.

*When Color matching is set to "ON", Auto picture control, Advanced color, Color temp., White balance and Offset are disable.

✐The mark "4" means that the available image mode in the selected input source. The error message appears when selecting the disabled image mode indicated with "*".

Image 36

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Features Internet IntranetNetwork specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN code169.254.100.100 255.255.0.0255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Sets Dhcp configuration ON/OFFMail setting Setting Smtp server and administrator address Setting Smtp authenticationRegistering and deleting E-mail addresses Check / DeleteSetting POP server Error message for sending alert mailExamples Type and contents of alert mail Snmp setting Enter community name to send Trap. Default name is publicPJ information Enter user name of the projector etc. optionalUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next PJ statusAbout projector condition Status DescriptionControl InputMeet the input signal are listed SystemItem Description Image adjustment Image mode Video ComputerPC adjustment Setting up the projector Screen settingLens adjustment Screen mode VideoInput source Normal Full Wide169 Zoom True Natural wide CustomSetting Resets the settings of Picture in Picture Stores the adjustment values. Select aMode no. User1 User5 from the pull Clear the adjustment values. SelectDefault, OFF Remote controlSets on or off the logo display on Shutter management...Sets the shutter management operationSets the color of the contents. Color Time, Network PIN code, Network settingSettings, etc Sets the digital processingInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Chapter Appendix Examples of connection Peer-To-Peer connectionGateway Router installed in the network To another networkUse of telnet ControlUse the IP address assigned to the projector Password 1234 is used for the example Command FunctionC00 Power on C01 Power off C05 Input C06 C07 C08 Menu display onWeb browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? OperationWhat is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KL8A