Sanyo Projector owner manual Lens adjustment, Input source, Screen mode Video

Page 39

Setting up the projector

Continue from the previous page.

Item Description

Screen aspect.....Sets the aspect ratio to fit the screen.

(Full, 16:9, 16:10, 4:3)

 

*Full is for flexible aspect ratio.

 

*Some Screen settings are limited

 

depending on the Screen aspect as

Keystone

shown in the below table.

Corrects the keystone distortion of the

 

projected image on the screen by press-

 

ing the Up/Down/Left/Right buttons.

 

Click Reset to reset the keystone correc-

Digital zoom

tion.

Adjusts the image zoom in and out at

 

computer input mode.

 

Click OFF to return the image to its nor-

Reset

mal size.

Resets the settings of Screen, Ceiling,

 

Rear, Screen aspect, Keystone and Digital

 

zoom.

Lens adjustment

Item

Description

Zoom

Adjusts the image zoom in and out.

Focus

Adjusts the focus of the image.

Lens shift

Positions to the desired point by pressing the Up/Down/Left/Right buttons.

 

Click Reset to return to the center position.

* Step(s)

Sets the effective steps (1-20 steps) by one pressing the +/- or Up/Down/Left/Right

 

buttons to adjust them quickly.

Screen Aspect

Full or 16:10

16:9

 

4:3

 

 

Input source

Input source

Input source

Screen mode

Video

PC

Video

 

PC

Video

 

PC

Normal

4

4

4

 

4

4

 

4

Full

4

4

4

 

4

4

 

4

Wide(16:9)

4

4

*1

 

*1

*3

 

4

Zoom

4

4

4

 

4

4

 

4

True

*1

4

*1

 

4

*1

 

4

Natural wide

*2

*1

*2

 

*1

*1

 

*1

Custom

4

4

4

 

4

4

 

4

The mark "4" means that the available screen mode in the selected input source system.

*1 The error message appears when selecting the disabled screen mode indicated with "*1".

*2 Natural widecannot be selected when 720p, 1035i, 1080i, 1080p or 2K is selected in AV system menu.

*3 Wide(16:9) can be selected when the video signal is 2K.

ENGLISH

39

Image 39
Contents Network Set-up and Operation Wired Setting Projector Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Internet Intranet FeaturesRequired operating environment for computers Network specifications of the projectorExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Network PIN code Numerical value is a setting example169.254.100.100 255.255.0.0255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Setting Display of main settingMain setting page in the display Sub menu tab Switches the sub menu tab Main menuExample of the setting How to use the settingSelect items by ticking on check boxes Select an item by selecting a radio buttonInitial setting Whats PJLink? Network PIN code settingPJLink and password setting To 32 alphanumeric characters can be used for the passwordSets Dhcp configuration ON/OFF Network configurationMail setting Check / Delete Setting Smtp server and administrator addressSetting Smtp authentication Registering and deleting E-mail addressesError message for sending alert mail Setting POP serverExamples Type and contents of alert mail Enter user name of the projector etc. optional Snmp settingEnter community name to send Trap. Default name is public PJ informationUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector PJ status Power control and status checkService in need Displays the status of the projectors power. Refer to nextStatus Description About projector conditionInput ControlMeet the input signal are listed SystemItem Description Image mode Video Computer Image adjustmentPC adjustment Screen setting Setting up the projectorNormal Full Wide169 Zoom True Natural wide Custom Lens adjustmentScreen mode Video Input sourceSetting Clear the adjustment values. Select Resets the settings of Picture in PictureStores the adjustment values. Select a Mode no. User1 User5 from the pullShutter management...Sets the shutter management operation Default, OFFRemote control Sets on or off the logo display onSets the digital processing Sets the color of the contents. ColorTime, Network PIN code, Network setting Settings, etcInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Chapter Appendix Peer-To-Peer connection Examples of connectionTo another network Gateway Router installed in the networkUse of telnet ControlUse the IP address assigned to the projector Menu display on Password 1234 is used for the exampleCommand Function C00 Power on C01 Power off C05 Input C06 C07 C08Web browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting Netscape Navigator JavaScript SettingSafari MAC OS X vHow can I restrict access from the computer Why doesn’t the setting page appear in my web browser?How can I install several projectors? Operation Why am I not receiving E-mail alert messages?What are the rules for IP address assignment? What is the MAC address assigned to the projector?Can I update the firmware of the projector SO-KL8A