Sanyo Projector Password 1234 is used for the example, Command Function, Menu display on

Page 51

Use of telnet

3.When communication is established correctly, the word "PASSWORD:" appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" key.

When the word "Hello" is replied, login has been succeeded.

*The password "1234" is used for the example.

4.Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projec- tor, and press "Enter" key. Confirm the projector is turning on.

*Enter with ASCII 64-byte capital characters and one-byte characters.

To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.

> close [return]

The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands.

Command list table

Command		Function
	C00	Power on
	C01	Power off
	C05	Input 1
	C06	Input 2
	C07	Input 3
	C08	Input 4
	C1C	Menu display on
	C1D	Menu display off

*1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). If the authentication of the entered password is failed 4 times continuously, the communication will be

disconnected automatically. Please try again for the connection.

✐If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection.

ENGLISH

51

Image 51

Contents Network Set-up and Operation Wired Setting Projector Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions Table of contents Chapter Internet Intranet FeaturesRequired operating environment for computers Network specifications of the projectorExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Network PIN code Numerical value is a setting example169.254.100.100 255.255.0.0255.255.255.255 Setup Procedures Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Setting Display of main settingMain setting page in the display Sub menu tab Switches the sub menu tab Main menuExample of the setting How to use the settingSelect items by ticking on check boxes Select an item by selecting a radio buttonInitial setting Whats PJLink? Network PIN code settingPJLink and password setting To 32 alphanumeric characters can be used for the passwordSets Dhcp configuration ON/OFF Network configurationMail setting Check / Delete Setting Smtp server and administrator addressSetting Smtp authentication Registering and deleting E-mail addressesError message for sending alert mail Setting POP serverExamples Type and contents of alert mail Enter user name of the projector etc. optional Snmp settingEnter community name to send Trap. Default name is public PJ informationUp to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector PJ status Power control and status checkService in need Displays the status of the projectors power. Refer to nextStatus Description About projector conditionInput ControlMeet the input signal are listed SystemItem Description Image mode Video Computer Image adjustmentPC adjustment Screen setting Setting up the projectorNormal Full Wide169 Zoom True Natural wide Custom Lens adjustmentScreen mode Video Input sourceSetting Clear the adjustment values. Select Resets the settings of Picture in PictureStores the adjustment values. Select a Mode no. User1 User5 from the pullShutter management...Sets the shutter management operation Default, OFFRemote control Sets on or off the logo display onSets the digital processing Sets the color of the contents. ColorTime, Network PIN code, Network setting Settings, etcInformation InformationItems Description Network Indication of the lamp status Indication of the filter statusStatus Chapter Appendix Peer-To-Peer connection Examples of connectionTo another network Gateway Router installed in the networkUse of telnet ControlUse the IP address assigned to the projector Menu display on Password 1234 is used for the exampleCommand Function C00 Power on C01 Power off C05 Input C06 C07 C08Web browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting Netscape Navigator JavaScript SettingSafari MAC OS X vHow can I restrict access from the computer Why doesn’t the setting page appear in my web browser?How can I install several projectors? Operation Why am I not receiving E-mail alert messages?What are the rules for IP address assignment? What is the MAC address assigned to the projector?Can I update the firmware of the projector SO-KL8A