Sanyo PLC-XL45 Part Names and Functions Remote Control Battery Installation, Operating Range

Page 12

Part Names and Functions

Remote Control Battery Installation

1

Open the battery

 

compartment lid.

2

Install new batteries into

3

Replace the

 

the compartment.

 

compartment lid.

Two AA size batteries

For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment.

To insure safe operation, please observe the following precautions: Use two (2) AA or LR6 type alkaline batteries.

Always replace batteries in sets.

Do not use a new battery with a used battery.

Avoid contact with water or liquid matter.

Do not expose the remote control to moisture or heat.

Do not drop the remote control.

If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

Risk of explosion if a battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Operating Range

Point the remote control toward the projector

 

(Infrared Remote Receiver) when pressing

 

any button. Maximum operating range for the

 

remote control is about 16.4’ (5 m) and 60

30°

degrees in front of the projector.

30°

16.4’ (5 m)

12

http://www.pureglare.com.au

Image 12
Contents Model PLC-XL45 Features and Design Security FeaturesTable of Contents Safety Precaution To the OwnerSafety Instructions Voor de klanten in NederlandSafety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communications Commission NoticePart Names and Functions Front BackBottom Exhaust VentsPart Names and Functions Rear Terminal Part Names and Functions Top Control Part Names and Functions Remote Control Part Names and Functions Remote Control Battery Installation Operating RangeInstallation Adjustable FeetPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Audio OUTInstallation Connecting the AC Power Cord Projector side AC outlet sideSelected Input Source and Lamp Mode Basic OperationTurning On the Projector PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote Control Select button On-Screen MenuTop Control Menu button Point buttonBasic Operation Menu Bar For computer sourceBasic Operation Focus Adjustment Remote ControlKeystone Correction Basic Operation Sound Adjustment Remote Control OperationBasic Operation No Show buttonComputer Input Input Source SelectionInput Menu Source Select MenuComputer Input Computer System Selection AutoPC System Menu ModeComputer Input Auto PC Adjustment Direct Operation Remote ControlTo store the adjusted parameters PC Adjust MenuComputer Input Manual PC Adjustment Computer Input Computer Input Image Level Selection Computer Input Image Level Adjustment Screen Size Adjustment Custom Digital zoom +Digital zoom Remote Control Menu Operation Video InputInput Source Selection Video, S-Video RGB Scart Video Input Video System Selection Video or S-Video AutoComponent Auto AV System Menu Video or S-VideoMenu Operation Remote Control Video Input Image Level SelectionCinema Image1-4Video Input Image Level Adjustment ColorTint Video Input Noise reductionProgressive Video Input Screen Size Adjustment Setting SettingLogo Logo and Logo PIN code lock settings Logo selectCapture Logo select CaptureEnter a Logo PIN code Logo PIN code lockCeiling RearTerminal Power management Input searchOn start Remote control On startLamp control To change the code for the projectorSecurity Key lock and PIN code lock Key lockPIN code lock Change the PIN code lock setting Change the PIN codeFactory default FanLamp counter Maintenance and Cleaning Then check the matters belowMaintenance and Cleaning Cleaning the Air Filters Attaching the Lens CoverMaintenance and Cleaning Cleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Maintenance and CleaningReset the lamp replacement counter Lamp Handling Precautions Maintenance and Cleaning Lamp Replacement CounterTroubleshooting AppendixAppendix Computer 2 cannot be selectedMenu Tree Computer Input/Video InputComputer Input Video Input Setting System AutoSettingAppendix Indicators and Projector Condition Projector ConditionAppendix Compatible Computer Specifications DisplayTechnical Specifications Accessories Optional PartsAppendix Configurations of Terminals DimensionsTerminal Mini DIN 8-PIN USB Connector Series B Appendix PIN Code Number Memo Logo PIN Code Lock NoKZ6AC
Related manuals
Manual 12 pages 48.79 Kb Manual 65 pages 27.11 Kb