Sanyo POA-PN40 owner manual Change the mode of the registered projector, Status

Page 59

Multi-control

Change the mode of the registered projector

To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button.

Mode	Operation
Control	Multi-controlling the projector
OFF	Excluding from the multi-control
Delete	Deleting from the multi-control

* This function is not available with the Light mode.

Status

If some of the registered projectors are disabled by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still active. At the same time, the deactivated projectors are excluded from the multi-control. The status of the registered projectors are indicated under the projec- tor name. See the table below for status indications.

	Status
Status	Description
(blank)	The projector is connected to the network correctly
No connect	The projector may not be connected to the network. Please check the connection and
	network configuration of this projector.
PIN code error	The PIN code is incorrect. The PIN code for the multi-controlled projectors must be
	the same. Change the PIN code of this projector to the common PIN code.

* The Network Unit updates the status at the time when the multi-control function was executed.

✐If the multi-controlled projector is in the standby mode, any change is not effective except timer setting.

✐It is recommended that a specified projector should be chosen for setting as a master when you use this multi-control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector.

✐If the registered projector is not connected to the network, it will take some time to complete the multi-control operation because of waiting for the response from each registered projector.

PJ-NET ORGANIZER

OWNER'S MANUAL

ENGLISH

59

Image 59

Contents PJ-Net Organizer Trademarks ComplianceFederal Communication Commission Notice Use of this manual Expression/AbbreviationContents Contents Page Chapter Preparation Snmp Agent function p.36 FeaturesWeb Management function p.39 Mail Alert function p.32Control port ready for external equipment p.61 Automatic On/Off using Clock function p.51Multi-control function p.56 Operating environment Package contains Before usePreparation Chapter Installation Function of the Network Unit p.15 Flow of installationInstallation and network configuration p.16-22 Name and function of each part Mounting Installation and network configurationConnection of LAN cable Selection of network menu Network configurationConfigure the network Confirmation of the network menuCompleting of installation Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Fixing the network configurationNetwork PIN code setting How to enter the numbers with the screen 10-key pallet Installation Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Main setting page in the Standard Mode display Display of main settingMain setting page in the Light Mode display How to use the settingText box setting Type of the setting palletWith the Network Unit Initial settingWhats PJLink? PJLink and password settingAuto setting Date and time settingNetwork configuration Setting Smtp server and administrator address Mail settingOption selection for sending alert mail Registering and deleting E-mail addressesExamples Type and contents of alert mail When the life span of lamp is reached PJ information Snmp settingSnmp setting Basic Setting and Operation Chapter Controlling the Projector Popup confirmation window Power control and status checkStatus Description About projector conditionInput ControlsSystem Available selection when the ComputerAnalog inputAvailable selection when the VIDEO/S-VIDEO input Available selection when the Y, Cb/Pb, Cr/Pr inputSelect an image mode Image adjustmentMenu SoundPC adjustment Input source Screen mode Video Computer Setting up the projectorLamp Corres. Value Reset Save/delete the settings Save the controls and settingsLoad a control set Check the saved itemsSet a day or date Timer settingHow to set the timer Select an event action Check the timer eventsChange the event mode Set an execute timeProjector Power Event Items Description Projector informationTime, replace lamp immediately Indication of the lamp statusMulti-control Controlling and setting the multi-projectorsStart/stop the multi control Confirmation of registered projector Register the projectorStatus Change the mode of the registered projectorControlling all together Conf. & Change page in the light modeSetting all together Chapter Use of Serial Port Use of Serial Port Serial port settingSetting examples for the serial control Example Control examplesPJ3 PJ2 PJ1 Preparation Use of telnetUse of telnet Control the projector with telnet Command list tableChapter Appendix Peer-To-Peer connection Examples of connectionEntrance hall Gateway Router installed in the networkProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional Internet Explorer ActiveScript settingExamples OS/Browsers Proxy setting Netscape Navigator JavaScript SettingProxy setting TCP/IP Product specificationSerial port specification Port specificationLAN port specification DNS How can I restrict access from the computer English You can register up to 10 addresses Can I control the projector by using the telnet application? Why am I not receiving E-mail alert messages?Can I update the firmware of the Network Unit? What are the rules for IP address assignment? What is the MAC address assigned to the Network Unit?1AA6P1P5006-- Idzg