Sanyo PDG-DWL2500 owner manual Cautious use of equipment with laser technology

Page 8

Safety Instructions

Installing the Projector in Proper Position

Install the projector properly. Improper installation may reduce the lamp life and cause fire hazard.

Do not roll the projector more than 10 degrees from side to side.

10˚

10˚

Do not roll the projector more than 5 degrees from side to side when front or rear is downward.

Do not put the projector on either side to project an image.

Note:

• Fix the projector when installing it so that the projector would not fall down.

CAUTION

Choose the running speed of cooling fans in the fan control setting according to the altitude in which the projector is being used (p.61). Failure to do so may affect the projector life.

CAUTION ON CEILING MOUNTING

For ceiling mounting, you need the ceiling mount kit designed for this projector. When not mounted properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

Cautious use of equipment with laser technology

Do not radiate strong light such as laser light on the projection lens directly, as this may degrade the functionality of the projector, and will void any applicable warranties.

Image 8
Contents 3D Ready Network SupportedTrademarks Features and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Moving the Projector Safety Instructions Air CirculationFilter Maintenance Cautious use of equipment with laser technology Compliance AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom Top Controls and Indicators w Infrared Remote Receiver Part Names and FunctionsFront q w e Rear Air Intake vent Projection WindowPart Names and Functions Side Terminal Part Names and Functions Top Controls and Indicators Part Names and Functions Remote Control Remote Control Operating Range Remote Control CodePositioning the Projector InstallationAdjustable Feet Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Monitor Output Signal TableFor Continental Europe For the U..K Installation Connecting the AC Power CordProjector side AC outlet side Selected Input Source and Lamp Control Basic OperationTurning On the Projector Basic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Direct OFF FunctionBasic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuBasic Operation Menu Bar Zoom + Basic Operation Zoom and Image Position AdjustmentFocus Adjustment Basic Operation Auto Setup Function Keystone CorrectionBasic Operation Sound Adjustment Volume Dialog BoxSound Menu VoumeBasic Operation Remote Control Operation Timer button Remote ControlTimer No Show buttonInput Menu Computer InputInput Source Selection Computer 1 RGB Computer Input Input Source Selection Computer 2 RGB Input MenuComputer Input Computer System Selection PC System MenuComputer Input Auto PC adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC adjustment Store Menu Mode free MenuComputer Input Computer Input Image Mode Selection Image Select MenuComputer Input Image Adjustment Image adjust MenuComputer Input Screen Size Adjustment Zoom + Remote Control Custom adjDigital zoom + Digital zoomKeystone RearInput Menu 4Note Video InputInput Source Selection Video, S-video Video Input Input Source Selection Component, Scart, Hdmi Component RGB ScartVideo Input Image Mode Selection Video Input Image Adjustment Noise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Video Input Screen Size Adjustment Screen MenuWide169 Natural wideKeystone For Viewing 3D Contents 3D DisplaySymptoms Possible problems Solution 3D DisplaySetting SettingSetting Menu Language Menu LanguageInput search Auto setupAuto setup 3D setting 3D settingPower off? p.22 Timer Logo Logo and Logo PIN code lock settingsDefault BackgroundLogo PIN code lock Capture Logo PIN code lockCapture Change the Logo PIN code lock setting Enter a Logo PIN code Logo PIN code changeEnter a Logo PIN code Logo PIN code changeHdmi setup Hdmi setupStandby mode TerminalPower management Direct onClosed caption Off, CC1, CC2, CC3 or CC4From Color to White 4Note Lamp controlPIN code lock Security Key lock and PIN code lockKey lock PIN code change Change the PIN code lock settingEnter a PIN code Lamp counter FanFan control Factory default Filter counterProjector InformationInput Source Information Display 4Note Then check the matters below Maintenance and CleaningTop Panel Filter counter Maintenance and Cleaning Replacing the FilterResetting the Filter Counter Maintenance and Cleaning Cleaning the Projection Window Cleaning the Projector CabinetService Parts No 351 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Maintenance and Cleaning Resetting the Lamp Counter Press Select button. Lamp replacement counterTroubleshooting AppendixAppendix Appendix Appendix Menu Tree Computer Input/HDMI Input/Video InputVideo Input Computer Input/HDMI Input/Video Input Appendix Indicators and Projector Condition Normal Condition Abnormal ConditionAppendix Compatible Computer Specifications Diplay800x600 37.879 60.320 Technical Specifications Appendix Optional Parts PJ Link NoticeModel No SCART-VGA CableAppendix Configurations of Terminals Logo PIN Code Lock No Appendix PIN Code Number MemoPIN Code Lock No Appendix Dimensions KG8AC