Hitachi CP-X265 user manual Connecting your devices, About Plug-and-Play capability

Page 11

Setting up

Connecting your devices

CAUTION ►Turn off all devices prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

►Use the accessory cable or a designated-type cable for the connection. Some cables have to be used with core set. A too long cable may cause a certain picture degradation. Please consult with your dealer for details. For cables that have a core only at one end, connect the core to the projector.

►Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

NOTE • Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

Secure the screws on the connectors and tighten.

Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

For some RGB signal modes, the optional Mac adapter is necessary.

When the image resolution is changed on a computer, depending on an input, automatic adjustment function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original.

It might be recommended to use other CRT or LCD monitors to change the resolution.

About Plug-and-Play capability

Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC 2B. Plug-and-Play can be achieved by connecting this projector to a computer is VESA DDC (display data channel) compatible.

Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug- and-Play monitor.

11

Image 11
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content About contents of package Fastening the lens cover Bottom side Part namesProjector Used for Ethernet When utilizingPorts See below Rear-Left sideControl buttons Remote controlSetting up 169 Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesUSB Connecting to a NetworkExamples of connection with a computer P R Examples of connection with a VCR/DVD playerComponent video out Component video cable P BAC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Gamma Adjust the level using the buttonsPicture Menu Light ó DarkColor Temp Picture Menu~Note~ MY MemoryPosition PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Normal ó Hinvert ó Vinvert ó H&VINVERT Setup MenuUsing the buttons / switches the mode for mirror status VolumeBlank Screen MenuMenu Position MyScreen Lock Screen MenuStart UP Message Auto on Option MenuAuto Search MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off IP Address Network MenuDhcp Network Menu Network Functions Lamp MaintenanceLamp cover Case of replacement by yourselfLamp Type number = CP-X256 DT00757, CP-X265 DT00751Handle Filter cover Air filterType number = NJ22222 Air filter’s knob Air filterWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications