Hitachi CP-X265 user manual Remote control, Putting batteries

Page 15

Remote control

Remote control

Putting batteries

WARNING ►Always handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.

And also improper use may result in cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Be sure to use only the batteries specified. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not short circuit or solder a battery.

Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.

If you observe a leakage of a battery, wipe out the flower and then replace a battery.

If the liquid adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

1.

2.

3.

Remove the battery cover.

Slide back and remove the battery cover in the direction of the arrow.

Insert the batteries.

Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

15

Image 15
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content About contents of package Fastening the lens cover Part names ProjectorBottom side Used for Ethernet When utilizingPorts See below Rear-Left sideControl buttons Remote controlSetting up 169 Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesConnecting to a Network Examples of connection with a computerUSB P R Examples of connection with a VCR/DVD playerComponent video out Component video cable P BAC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Gamma Adjust the level using the buttonsPicture Menu Light ó DarkColor Temp Picture Menu~Note~ MY MemoryPosition PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Normal ó Hinvert ó Vinvert ó H&VINVERT Setup MenuUsing the buttons / switches the mode for mirror status VolumeScreen Menu Menu PositionBlank Screen Menu Start UPMyScreen Lock Message Option Menu Auto SearchAuto on MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionUsing the PIN Lock Function Turning the Password offRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Network Menu DhcpIP Address Network Menu Network Functions Lamp MaintenanceLamp cover Case of replacement by yourselfLamp Type number = CP-X256 DT00757, CP-X265 DT00751Air filter Type number = NJ22222Handle Filter cover Air filter’s knob Air filterReplacing Internal Clock battery Take the old battery outWill come up. Remove the battery Put a new battery Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications