Hitachi CP-X265 user manual Image Menu, Over Scan, Position, Phase

Page 30

IMAGE Menu

IMAGE Menu

With the IMAGE menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

2+%674'

#5 '%6



/#)'

18'4

%#0



+02 6

 

 

2

*

 

 



 

 

 

*#5'



12

 

 

5+<'215+6+10 

0'%4''06+19 -

#76 #&,756 ':'%76'

'#5;/'07

 

 

 

 

Item

Description

 

 

 

Using the buttons ▲/▼ switches the mode for aspect ratio.

 

For an RGB signal

 

NORMAL ó 4:3 ó 16:9 ó SMALL

ASPECT

For a video signal, s-video signal or component video signal

4:3 ó 16:9 ó 14:9 ó SMALL

 

 

For a no signal

 

4:3 (fixed)

 

• The NORMAL mode keeps the original aspect ratio of the signal.

 

Using the buttons ▲/▼ adjusts the over-scan ratio.

OVER SCAN

Large (It reduces picture) ó Small (It magnifies picture)

• This item can be selected only for a video, s-video and component signal.

 

• When this adjustment is too large, certain degradation may appear

 

at the frame area of the picture. In such a case, please adjust small.

 

Using the buttons ▲/▼ adjusts the vertical position.

 

Up ó Down

 

Over-adjusting the vertical position may cause noise to appear

V POSITION

on the screen. If this occurs please reset the vertical position to the

default setting. Pressing the RESET button when V POSITION is

 

selected will reset the V POSITION to the default setting.

 

For a video signal, s-video signal or component video signal

 

The adjustable range of V.POSITION depends on the OVERSCAN setting.

 

It is not possible to adjust when the OVERSCAN is set to 10.

 

Using the buttons ▲/▼ adjusts the horizontal position.

 

Left ó Right

 

Over-adjusting the horizontal position may cause noise to appear

H POSITION

on the screen. If this occurs please reset the horizontal position to

the default setting. Pressing the RESET button when H POSITION

 

is selected will reset the H POSITION to the default setting.

 

For a video signal, s-video signal or component video signal

 

The adjustable range of H.POSITION depends on the OVERSCAN setting.

 

It is not possible to adjust when the OVERSCAN is set to 10.

 

Using the buttons ▲/▼ adjusts the horizontal phase to eliminate flicker.

H PHASE

Right ó Left

• This item can be selected only for an RGB signal or a component

 

 

video signal.

30

Image 30
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content About contents of package Fastening the lens cover Part names ProjectorBottom side Rear-Left side When utilizingPorts See below Used for EthernetRemote control Control buttonsSetting up Arrangement 169 DownAdjusting the projectors elevator Elevator feet Elevator buttonUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately Connecting your devices About Plug-and-Play capabilityConnecting to a Network Examples of connection with a computerUSB P B Examples of connection with a VCR/DVD playerComponent video out Component video cable P RConnecting power supply AC inlet Connector Power cordRemote control Putting batteriesUsing the remote control Changing the signal setting for the projectors remote sensorTurning off the power Power on/offTurning on the power Off. Attach the lens coverOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalAdjusting the zoom and focus Selecting an aspect ratio For a video signal or s-video signal Using the automatic adjustment featureAdjusting the position  For a component video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMenu button Enter button Cursor buttons Reset button Multifunctional settingsUsing the menu function Easy MenuEasy Menu Easy Menu Light ó Dark Adjust the level using the buttonsPicture Menu GammaPicture Menu Color TempMY Memory ~Note~Over Scan PhaseImage Menu PositionFor a component video signal For a video signal or s-video signalAuto Adjust Image MenuVideo NR Input MenuProgressive Color SpaceVideo Format Input MenuComponent Frame LockCustom Resolution Setup Menu Volume Setup MenuUsing the buttons / switches the mode for mirror status Normal ó Hinvert ó Vinvert ó H&VINVERTScreen Menu Menu PositionBlank Screen Menu Start UPMyScreen Lock Message Option Menu Auto SearchAuto on Lamp Time Option MenuAuto OFF MY ButtonGhost ServiceFAN Speed Filter MessageUse the / button to change the Projectors remote sensor Factory ResetRemote Freq InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off Network Menu DhcpIP Address Network Menu Network Functions Maintenance LampType number = CP-X256 DT00757, CP-X265 DT00751 Case of replacement by yourselfLamp Lamp coverAir filter Type number = NJ22222Handle Filter cover Air filter Air filter’s knobReplacing Internal Clock battery Take the old battery outWill come up. Remove the battery Put a new battery Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationsSpecifications