Hitachi CP-X265 user manual Setup Menu

Page 35

SETUP Menu

SETUP Menu

With the SETUP menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

2+%674'

#761-';5610'

':'%76'

/#)'

 

-'; 610'



+02 6

 

9*+52

4

 

2

 

/+44

014/#.

0'12%4''06+19

-

#7&+181.7/'

'#5;/'07

 

 

 

Item

Description

 

Selecting this item performs the Automatic keystone distortion

 

correction. Projector automatically corrects vertical keystone

 

distortion due to the (forward/backward) setup angle by itself.

 

• This function will be executed only once when selected in the

 

Menu. When the slant of the projector is changed, executes this

 

function again.

 

• When V:INVERT or H&V:INVERT is selected to the MIRROR item

AUTO

in the SETUP menu, if the projector screen is inclined or angled

downward, this function may not work correctly.

KEYSTONE

EXECUTE

• When the zoom adjustment is set to the TELE (telephoto focus),

 

this correction may be excessive. This function should be used

 

when the zoom adjustment is set to the WIDE (wide-angle focus)

 

whenever possible.

 

• When vertical degree is almost 0 degree, the automatic keystone

 

distortion correction may not work.

 

• When vertical degree is over ±30 degree, the automatic keystone

 

distortion correction may not work well.

 

• This function will be unavailable when Transition Detector is on (48).

 

Using the buttons ▲/▼ corrects the keystone distortion.

KEYSTONE

Upper in the data ó Lower in the data

• The adjustable range of this function will vary with the type of input

 

signal. At some signals, this function may not work well.

 

• This function will be unavailable when Transition Detector is on (48).

 

Using the buttons ▲/▼ turns off/on the whisper mode.

WHISPER

NORMAL ó WHISPER

• When the WHISPER is selected, acoustic noise and screen

 

 

brightness are reduced.

35

Image 35
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content About contents of package Fastening the lens cover Bottom side Part namesProjector Used for Ethernet When utilizingPorts See below Rear-Left sideControl buttons Remote controlSetting up 169 Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesUSB Connecting to a NetworkExamples of connection with a computer P R Examples of connection with a VCR/DVD playerComponent video out Component video cable P BAC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Gamma Adjust the level using the buttonsPicture Menu Light ó DarkColor Temp Picture Menu~Note~ MY MemoryPosition PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Normal ó Hinvert ó Vinvert ó H&VINVERT Setup MenuUsing the buttons / switches the mode for mirror status VolumeBlank Screen MenuMenu Position MyScreen Lock Screen MenuStart UP Message Auto on Option MenuAuto Search MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off IP Address Network MenuDhcp Network Menu Network Functions Lamp MaintenanceLamp cover Case of replacement by yourselfLamp Type number = CP-X256 DT00757, CP-X265 DT00751Handle Filter cover Air filterType number = NJ22222 Air filter’s knob Air filterWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications