Hitachi CP-X265 user manual Air filter, Type number = NJ22222, Handle Filter cover

Page 55

Maintenance

Air filter

WARNING ►Before caring, make sure the power switch is off and the power cable is not plugged in, then allow the projector to cool sufficiently. The care in a high temperature state of the projector could cause an electric shock, a burn and/or malfunction to the projector.

►Use only the air filter of the specified type. Do not use the projector with the air filter and the filter cover removed. It could result in a fire and/or malfunction to the projector.

►The air filter should be cleaned periodically. If the air filter becomes clogged by dust or the like, internal temperatures rise and could cause a fire, a burn and/or malfunction to the projector.

NOTE • Please replace the air filter when it is damaged or too soiled, and

also when you replace the lamp.

•Please reset the filter time only when you have cleaned or replaced the air filter, for a suitable indication about the air filter. (41)

•The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

If the air filter becomes clogged by dust or the like, internal temperatures rise and could cause a fire, a burn and/or malfunction to the projector. When the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible.

Please check and clean the air filter periodically, even if there is no message. Please replace the air filter when it is damaged or too soiled. Preparation of a new air filter is recommended.

To prepare a new air filter, contact your dealer and tell the air filter type number.

Type number = NJ22222

And also when you replace the lamp, please replace the air filter. An air filter of specified type will come together with a replacement lamp for this projector.

1. Turn the projector off, and unplug the power cord. Allow the lamp to cool for at

least 45 minutes.

2. When the projector is suspended from the ceiling, apply the vacuum cleaner to

and around the filter cover first, to prevent penetration of dust or the like.

3. While supporting the projector with one hand, use your other hand to pull the filter

cover forward in the direction of the arrow. Remove the air filter.

Handle

Filter cover

55

Image 55

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content About contents of package Fastening the lens cover Projector Part namesBottom side Used for Ethernet When utilizingPorts See below Rear-Left sideControl buttons Remote controlSetting up 169 Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorHow to attach Using the Security BarSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a NetworkUSB P R Examples of connection with a VCR/DVD playerComponent video out Component video cable P BAC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Gamma Adjust the level using the buttonsPicture Menu Light ó DarkColor Temp Picture Menu~Note~ MY MemoryPosition PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Normal ó Hinvert ó Vinvert ó H&VINVERT Setup MenuUsing the buttons / switches the mode for mirror status VolumeMenu Position Screen MenuBlank Start UP Screen MenuMyScreen Lock Message Auto Search Option MenuAuto on MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Dhcp Network MenuIP Address Network Menu Network Functions Lamp MaintenanceLamp cover Case of replacement by yourselfLamp Type number = CP-X256 DT00757, CP-X265 DT00751Type number = NJ22222 Air filterHandle Filter cover Air filter’s knob Air filterTake the old battery out Replacing Internal Clock batteryWill come up. Remove the battery Put a new battery Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications