Hitachi CP-X265 user manual Turning Off the PIN Lock Function, If you have forgotten your PIN Code

Page 47

OPTION Menu

+PRWV 2+0%QFG 4)$

PIN BOX

%QPHKTOCVKQP 4)$

CONFIRMATION BOX

(PIN BOX)

OPTION Menu (continued)

Item

Description

SECURITY

3.1-3 Input a 4 part PIN Code using the ▲/▼/◄/►

/RGB and INPUT buttons. A CONFIRMATION BOX will appear. Reenter the

same PIN Code. This will complete the PIN Code registration.

NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat the process from 3.1-1.

Afterwards, anytime the projector is restarted after

the power switch is turned off the PIN BOX will be displayed. Enter the registered PIN Code.

The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.

If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.

This function will activate only when the projector is started after the power switch was turned off.

NOTE : Please do not forget your PIN Code.

3.2 Turning Off the PIN LOCK Function

3.2-1 Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.

Enter the registered PIN Code to turn the PIN LOCK function off. If an incorrect PASSWORD is entered the menu will close.

3.3 If you have forgotten your PIN Code

3.3-1 While the PIN BOX is displayed, press and hold the RESET button for three seconds or press and hold the INPUT and ► buttons for three seconds. The 10 digit Inquiring Code will be displayed.

NOTE: If there is no key input for about 5 minutes while the Inquiring Code is displayed the projector will turn off.

+PSWKTKPI %QFG

Inquiring Code

(PIN Code)

3.3-2 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.

47

Image 47

Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content About contents of package Fastening the lens cover Bottom side Part namesProjector Used for Ethernet When utilizingPorts See below Rear-Left sideControl buttons Remote controlSetting up 169 Down ArrangementElevator feet Elevator button Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesUSB Connecting to a NetworkExamples of connection with a computer P R Examples of connection with a VCR/DVD playerComponent video out Component video cable P BAC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlOff. Attach the lens cover Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal For a component video signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlEasy Menu Multifunctional settingsUsing the menu function Menu button Enter button Cursor buttons Reset buttonEasy Menu Easy Menu Gamma Adjust the level using the buttonsPicture Menu Light ó DarkColor Temp Picture Menu~Note~ MY MemoryPosition PhaseImage Menu Over ScanImage Menu For a video signal or s-video signalAuto Adjust For a component video signalColor Space Input MenuProgressive Video NRFrame Lock Input MenuComponent Video FormatCustom Resolution Setup Menu Normal ó Hinvert ó Vinvert ó H&VINVERT Setup MenuUsing the buttons / switches the mode for mirror status VolumeBlank Screen MenuMenu Position MyScreen Lock Screen MenuStart UP Message Auto on Option MenuAuto Search MY Button Option MenuAuto OFF Lamp TimeFilter Message ServiceFAN Speed GhostInformation Factory ResetRemote Freq Use the / button to change the Projectors remote sensorSecurity Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password FunctionRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off IP Address Network MenuDhcp Network Menu Network Functions Lamp MaintenanceLamp cover Case of replacement by yourselfLamp Type number = CP-X256 DT00757, CP-X265 DT00751Handle Filter cover Air filterType number = NJ22222 Air filter’s knob Air filterWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page Related messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Regarding the indicator lamps Signal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is workingSpecifications Warranty and after-serviceSpecifications