Hitachi CP-X268A Electrical power cord is not plugged, Power switch is not set to the on position

Page 66

Troubleshooting

Phenomena that may be easy to be mistaken for machine defects

WARNING ►Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.

1. Before requesting repair, please check in accordance with the following chart. This operation sometimes

resolves your problem.

If the situation cannot be corrected,

C

 

 

B/PB

 

 

C

 

 

R/PR

 

 

VIDEO

A

A

 

S-

 

 

SD CARD

AUXDCI/O5V

RGB IN2

CONTROL

0.5A

 

 

LAN

 

RGB

OUT

 

 

 

 

A

 

 

 

UDIO

OUT

2.

USB

The projector’s microprocessor may need to

be reset. Please push the Restart switch by using a cocktail stick or similar

and the projector will restart.

3. Some setting may be wrong. Please use the FACTORY RESET function of the SERVICE item in the OPTION menu (45) to reset all settings to factory default.

Then, if the problem is not removed after the remedy, please contact your dealer or service company.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

 

 

 

The electrical power cord is not plugged in.

15

 

Correctly connect the power cord.

 

 

 

The power switch is not set to the on position.

19

 

Set the power switch to [ ] (On).

 

 

 

The main power source has been interrupted during

 

Power does not

operation such as by a power outage (blackout), etc.

19

Please turn the power off, and allow the projector to cool

come on.

down at least 2 minutes, then turn the power on again.

 

 

 

 

Either there is no lamp and/or lamp cover, or either

 

 

of these has not been properly fixed.

 

 

Please turn the power off, and allow the projector to cool down

64, 65

 

at least 45 minutes. After the projector has sufficiently cooled

 

 

 

down, please make confirmation of the attachment state of the

 

 

lamp and lamp cover, and then turn the power on again.

 

 

The signal cables are not correctly connected.

13, 14

 

Correctly connect the connection cables.

 

 

Neither sounds

Signal source does not correctly work.

 

nor pictures are

Correctly set up the signal source device by referring to the

–

outputted.

manual of the source device.

 

 

The input changeover settings are mismatched.

20, 21

 

Select the input signal, and correct the settings.

 

 

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Content Contents of package How to use the Slot cover lockProjector features PreparationsFastening the lens cover Part names Bottom sideComponent CB/PBCR/PR Remote control Control buttonsMagnify Setting up Arrangement Min Max DownAdjusting the projectors elevator Elevator feetUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately Connecting your devices About Plug-and-Play capabilityConnecting to a Network and USB Memory Examples of connection with a computerUSB CB/PB CR/PRConnecting power supply AC inlet Connector Power cordInserting an SD Card and USB Memory Remote control Putting batteriesUsing the remote control Changing the signal setting for the projectors remote sensorTurning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalAdjusting the zoom and focus  For a no signal For an RGB signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMenu button Enter button Cursor buttons Reset button Multifunctional settingsUsing the menu function Easy MenuEasy Menu Easy Menu Light ó Dark Adjust the level using the buttonsPicture Menu GammaPicture Menu Color TempMY Memory Over Scan PhaseImage Menu PositionAuto Adjust Image MenuSize Video NR Input MenuProgressive Color SpaceVideo Format Input MenuComponent Frame LockCustom Resolution Setup Menu Volume Setup MenuUsing the buttons / switches the mode for mirror status AudioScreen Menu Menu PositionBlank MyScreen Screen MenuStart UP MyScreen LockMessage No Input is DetectedSync is OUT of Range Source NameAuto Search Option MenuTurn on  Turn OFF Auto onLamp Time Option MenuAuto OFF MY ButtonGhost ServiceFAN Speed Filter MessageUse the / button to change the Projectors remote sensor Factory ResetRemote Freq InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordUsing the PIN Lock Function Turning the Password offRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Setting the Transition Detector off MIU Menu Live ModeSee Live Mode in User’s Manual Network Functions for PresentationMIU Menu Dhcp Dynamic Host Configuration ProtocolSetup OperationSubnet Mask Default GatewayIP Address Time DifferenceEncryption Network ModeMode SpeedMIU Restart Maintenance LampCase of replacement by yourself LampType number = DT00751 Air filter Type number = NJ22222Handle Filter cover Air filter Air filter’s knobReplacing Internal Clock battery Take the old battery outWill come up. Remove the battery Put a new battery Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationsSpecifications
Top Page Image Contents