Part names
Ports (See below.)
CB/PB |
|
|
| SD | CARD |
|
|
|
|
|
CR/PR |
|
|
|
|
|
|
|
|
| |
|
| RGB |
|
|
|
|
|
| ||
VIDEO |
| A | IN1 | A |
|
|
|
| ||
A | UDIO |
| UXDCI/O |
|
|
|
| |||
S- | UDIO IN2 | IN1 |
| 5V 0.5A |
|
|
|
| ||
VIDEO |
|
|
|
| RGB IN2 |
|
| LAN |
| |
|
|
|
|
| CO | NTROL | RGB | OUT |
|
|
|
|
|
|
|
| UDIO |
| |||
|
|
|
|
|
|
|
|
| A | OUT |
|
|
|
|
|
|
| USB |
|
|
|
AC | IN |
|
Power switch (19)
AC inlet (15)
Elevator button (10) Elevator foot (10)
Vent
|
| AUDIO IN1 port (13) |
| |||
|
| (In the default setting, the AUDIO IN1 port is the audio | ||||
AUDIO IN3 L/R port (14) | port for the RGB IN1 port, however, it is possible to | |||||
change the settings. 38) |
| |||||
(In the default setting, the |
|
|
| SD CARD slot (13) | ||
AUDIO IN3 L/R port is the audio |
|
| ||||
RGB IN1 port (13) | This slot is used when | |||||
port for the VIDEO, | ||||||
and COMPONENT VIDEO |
| Restart switch (*) (66) | utilizing SD CARD. | |||
ports, however it is possible to | AUX I /O port (13) | |||||
RGB IN2 port (13) | ||||||
change the settings. 38) |
| This port is used when | ||||
|
| SD CARD |
| utilizing USB Memory. | ||
COMPONENT |
| AUX I/O |
| |||
|
|
|
| LAN |
| |
VIDEO ports (14) |
| AUDIO IN3 |
|
| LAN port (13) | |
Y | R |
|
| Used for Ethernet | ||
Y |
| AUDIO IN1 |
|
| ||
|
|
| input/output. | |||
| RGB IN1 | RGB IN2 | RGB OUT AUDIO OUT |
| ||
CB/PB | CB/PB | L |
|
| This port is used | |
CR/PR |
| AUDIO IN2 |
|
| ||
CR/PR | K | CONTROL | when utilizing network | |||
|
|
| USB | |||
|
|
| functions. | |||
VIDEO port (14) | VIDEO |
|
|
|
| |
|
|
|
|
| ||
|
|
| Ports | AUDIO OUT port | ||
|
|
|
| |||
|
|
|
|
| (13) | |
AUDIO IN2 port (13) |
|
| USB port (13) | RGB OUT port (13) | ||
(In the default setting, the AUDIO |
|
|
| |||
IN2 port is the audio port for | CONTROL port (13) |
| ||||
the RGB IN2 port, however, it is |
| |||||
possible to change the settings. Kensington lock slot |
| |||||
38) |
|
|
|
|
| |
NOTE (*) About Restart switch: This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances.