Hitachi CP-X268A user manual Part names, Bottom side

Page 5

Part names

Projector

Lamp cover (58) (Lamp unit is inside.)

Zoom ring (21)

Focus ring (21)

Vent

Lens (19)

Control buttons (7)

Remote sensor (18) Speaker

Security bar (11) (Use for attaching a commercial anti-theft chain or wire.)

Elevator button (10)

Front-Right side Lens cover (4)

OUT

USB

UDIOA

OUT

RGB

CONTR

LAN

2IN

RGB

VIDEO-

1IN

5A.

1IN

UDIOAUDIOA

VIDEOR

I/O

XUD

RGB

CARD SD

/PRC

B/PB

3IN

UDIOA

Elevator foot (10)

Filter cover (59)

(Air filter and intake vent are inside.)

Bottom side

WARNING ►During use or immediately after use, do not touch around the lamp and vents of the projector. (ê) It could cause a burn.

Image 5

Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content How to use the Slot cover lock Contents of packageFastening the lens cover Projector featuresPreparations Bottom side Part namesCR/PR ComponentCB/PB Magnify Remote controlControl buttons Setting up Min Max Down ArrangementElevator feet Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesUSB Connecting to a Network and USB MemoryExamples of connection with a computer CR/PR CB/PBAC inlet Connector Power cord Connecting power supplyInserting an SD Card and USB Memory Putting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlTurning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal  For a no signalAdjusting the position Using the automatic adjustment feature For an RGB signal  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsMenu button Enter button Cursor buttons Reset button Easy MenuEasy Menu Easy Menu Picture Menu Adjust the level using the buttonsLight ó Dark GammaColor Temp Picture MenuMY Memory Image Menu PhaseOver Scan PositionSize Auto AdjustImage Menu Progressive Input MenuVideo NR Color SpaceComponent Input MenuVideo Format Frame LockCustom Resolution Setup Menu Using the buttons / switches the mode for mirror status Setup MenuVolume AudioBlank Screen MenuMenu Position Start UP Screen MenuMyScreen MyScreen LockSync is OUT of Range No Input is DetectedMessage Source NameTurn on  Turn OFF Option MenuAuto Search Auto onAuto OFF Option MenuLamp Time MY ButtonFAN Speed ServiceGhost Filter MessageRemote Freq Factory ResetUse the / button to change the Projectors remote sensor InformationInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off See Live Mode in User’s Manual Network Functions for Live ModeMIU Menu PresentationSetup Dhcp Dynamic Host Configuration ProtocolMIU Menu OperationIP Address Default GatewaySubnet Mask Time DifferenceMode Network ModeEncryption SpeedMIU Restart Lamp MaintenanceType number = DT00751 Case of replacement by yourselfLamp Handle Filter cover Air filterType number = NJ22222 Air filter’s knob Air filterWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecifications Warranty and after-serviceSpecifications