Hitachi CP-X268A user manual Inserting an SD Card and USB Memory

Page 16

Setting up

Inserting an SD Card and USB Memory

When using the projector with a wireless LAN please insert the included Wireless Network Card.

When using a commercial SD Memory card in order to view images insert the SD Memory card in the same manner.

And when using a commercial USB MEMORY in order to view images insert the USB MEMORY to the AUX I/O port. (13)

See User's Manual - Network Function for information on using either type of card.

1. Make sure the projector’s power switch is OFF.

2. Remove the SD card slot cover.

Lift the cover slightly by the small indentation in the middle of the front of the cover using a finger nail or other means.

 Pull the cover forward and remove it completely from the projector.

3.Insert the SD card.

Slowly insert the SD card completely into

the SD card slot.

Make sure the angled corner of the SD card is facing the right side (AUX I/O port side) of the projector while inserting.

Indentation

AUX I/O Port

SD Card Slot

Angled corner

4. Replace the SD card slot cover.

Replace the cover by reversing the procedure used when removing the cover.

NOTE • When using the projector with a wired LAN, please remove the Wireless Network card.

•Select the "REMOVE MEDIA" on MIU menu before SD card or USB memory is removed.

NOTE • The LED becomes downward in some USB Memory. Remove the USB Memory after the accessing is completely finished.

IMPORTANT NOTE • To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

16

Image 16

Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content Contents of package How to use the Slot cover lockPreparations Projector featuresFastening the lens cover Part names Bottom sideCB/PB ComponentCR/PR Control buttons Remote controlMagnify Setting up Arrangement Min Max DownAdjusting the projectors elevator Elevator feetHow to attach Using the Security BarSecurity Bar Anti-theft chain or wire sold separately Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a Network and USB MemoryUSB CB/PB CR/PRConnecting power supply AC inlet Connector Power cordInserting an SD Card and USB Memory Remote control Putting batteriesUsing the remote control Changing the signal setting for the projectors remote sensorPower on/off Turning on the powerTurning off the power STANDBY/ONAdjusting the volume Selecting an input signalOperating Temporarily muting the soundSearching an input signal Adjusting the zoom and focusSelecting an input signal  For a no signalUsing the automatic adjustment feature Adjusting the position For an RGB signal  For a video signal or s-video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenAvailable function Remote control operation Operating the computer screenUSB mouse and keyboard control Move pointerMultifunctional settings Using the menu functionMenu button Enter button Cursor buttons Reset button Easy MenuEasy Menu Easy Menu Adjust the level using the buttons Picture MenuLight ó Dark GammaPicture Menu Color TempMY Memory Phase Image MenuOver Scan PositionImage Menu Auto AdjustSize Input Menu ProgressiveVideo NR Color SpaceInput Menu ComponentVideo Format Frame LockCustom Resolution Setup Menu Setup Menu Using the buttons / switches the mode for mirror statusVolume AudioMenu Position Screen MenuBlank Screen Menu Start UPMyScreen MyScreen LockNo Input is Detected Sync is OUT of RangeMessage Source NameOption Menu Turn on  Turn OFFAuto Search Auto onOption Menu Auto OFFLamp Time MY ButtonService FAN SpeedGhost Filter MessageFactory Reset Remote FreqUse the / button to change the Projectors remote sensor InformationUsing Security Features Inputting the PasswordChanging the Password SecurityUsing the MyScreen Password Function Description If you have forgotten your PasswordTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code Turning Off the PIN Lock Function If you have forgotten your PIN CodeSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off Live Mode See Live Mode in User’s Manual Network Functions forMIU Menu PresentationDhcp Dynamic Host Configuration Protocol SetupMIU Menu OperationDefault Gateway IP AddressSubnet Mask Time DifferenceNetwork Mode ModeEncryption SpeedMIU Restart Maintenance LampLamp Case of replacement by yourselfType number = DT00751 Type number = NJ22222 Air filterHandle Filter cover Air filter Air filter’s knobTake the old battery out Replacing Internal Clock batteryWill come up. Remove the battery Put a new battery Page Troubleshooting There is no input signalInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Electrical power cord is not plugged Power switch is not set to the on positionSignal cables are not correctly connected Signal source does not correctly workVolume is adjusted to an extremely low level Audio setting is not correctColor settings are not correctly adjusted Color Space setting is not suitableNot properly adjusted Either the focus and/or horizontal phase settings areWhisper function is working Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationsSpecifications