Hitachi CP-X268A user manual Setup Menu

Page 37

SETUP Menu

SETUP Menu

With the SETUP menu, the items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it referring to the following table.

2+%674'

#761-';5610'

':'%76'

/#)

-'; 610'

 



02 6

9*+52

014/#.

%4''20

81/+44.7/'4

126+1

#7&+1

 

 

/+7

 

 

 

'#5;/'07

 

 

 

Item

Description

 

Selecting this item performs the Automatic keystone distortion

 

correction. Projector automatically corrects vertical keystone

 

distortion due to the (forward/backward) setup angle by itself.

 

• This function will be executed only once when selected in the

 

Menu. When the slant of the projector is changed, executes this

 

function again.

 

• When V:INVERT or H&V:INVERT is selected to the MIRROR item

AUTO

in the SETUP menu, if the projector screen is inclined or angled

downward, this function may not work correctly.

KEYSTONE

EXECUTE

• When the zoom adjustment is set to the TELE (telephoto focus),

 

this correction may be excessive. This function should be used

 

when the zoom adjustment is set to the WIDE (wide-angle focus)

 

whenever possible.

 

• When vertical degree is almost 0 degree, the automatic keystone

 

distortion correction may not work.

 

• When vertical degree is over ±30 degree, the automatic keystone

 

distortion correction may not work well.

 

• This function will be unavailable when Transition Detector is on (50).

 

Using the buttons ▲/▼ corrects the keystone distortion.

KEYSTONE

Upper in the data ó Lower in the data

• The adjustable range of this function will vary with the type of input

 

signal. At some signals, this function may not work well.

 

• This function will be unavailable when Transition Detector is on (50).

 

Using the buttons ▲/▼ turns off/on the whisper mode.

WHISPER

NORMAL ó WHISPER

• When the WHISPER is selected, acoustic noise and screen

 

 

brightness are reduced.

37

Image 37
Contents Thank you for purchasing this projector About this manualTrademark acknowledgment Content How to use the Slot cover lock Contents of packagePreparations Projector featuresFastening the lens cover Bottom side Part namesCB/PB ComponentCR/PR Control buttons Remote controlMagnify Setting up Min Max Down ArrangementElevator feet Adjusting the projectors elevatorHow to attach Using the Security BarSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a Network and USB MemoryUSB CR/PR CB/PBAC inlet Connector Power cord Connecting power supplyInserting an SD Card and USB Memory Putting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlTurning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal  For a no signalAdjusting the position Using the automatic adjustment feature For an RGB signal  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsMenu button Enter button Cursor buttons Reset button Easy MenuEasy Menu Easy Menu Picture Menu Adjust the level using the buttonsLight ó Dark GammaColor Temp Picture MenuMY Memory Image Menu PhaseOver Scan PositionImage Menu Auto AdjustSize Progressive Input MenuVideo NR Color SpaceComponent Input MenuVideo Format Frame LockCustom Resolution Setup Menu Using the buttons / switches the mode for mirror status Setup MenuVolume AudioMenu Position Screen MenuBlank Start UP Screen MenuMyScreen MyScreen LockSync is OUT of Range No Input is DetectedMessage Source NameTurn on  Turn OFF Option MenuAuto Search Auto onAuto OFF Option MenuLamp Time MY ButtonFAN Speed ServiceGhost Filter MessageRemote Freq Factory ResetUse the / button to change the Projectors remote sensor InformationInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code If you have forgotten your PIN Code Turning Off the PIN Lock FunctionSetting the Transition Detector Password Using the Transition Detector FunctionTurning On the Transition Detector Function Setting the Transition Detector off See Live Mode in User’s Manual Network Functions for Live ModeMIU Menu PresentationSetup Dhcp Dynamic Host Configuration ProtocolMIU Menu OperationIP Address Default GatewaySubnet Mask Time DifferenceMode Network ModeEncryption SpeedMIU Restart Lamp MaintenanceLamp Case of replacement by yourselfType number = DT00751 Type number = NJ22222 Air filterHandle Filter cover Air filter’s knob Air filterTake the old battery out Replacing Internal Clock batteryWill come up. Remove the battery Put a new battery Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecifications Warranty and after-serviceSpecifications