Hitachi CP-X268A Using the Transition Detector Function, Setting the Transition Detector Password

Page 50
ENTER PASSWORD
BOX (small)
37+60':6
CHECK PASSWORD
BOX '06'4 ':+6
PASSWORD BOX
37+60':6
674674001((10
Transition Detector
on/off menu
FKUCDNGHTQO+H6JG[QWRTQLGEVQTRTGXKQWUN[6TCYKUJQPUKVKQPUETGGPVQJCU2+0JCXGKPUVCNNGF&GVGEVQTDGGP$CICKP1:CUSWCTGVTRQUKVKQPPUHGTTGFQPKOCIG/GPW
Transition Detector Alarm

OPTION Menu

OPTION Menu (continued)

Item

Description

SECURITY

4. Using the Transition Detector Function

While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.

•Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.

•Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.

•Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON.

4.1 Turning On the Transition Detector Function

4.1-1 Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu. Select TURN ON and the current

angle and mirror setting will be recorded. NOTE: This feature may not function properly if the projector

is not in a stable position when TURN ON is selected.

4.1-2 If this function is set to TURN ON when the vertical angle of the projector or mirror setting at which the projector is turned on is different than the previously recorded the Transition Detector Alarm will be displayed and the projector will not display the input signal.

Set the Transition Detector off in the SECURITY menu to display the input signal.

If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after the power switch was turned off.

4.2 Setting the Transition Detector PASSWORD

4.2-1 Use the ▲/▼ buttons on the SECURITY menu to select Transition Detector and press the ► or the ENTER button to display the Transition Detector on/off menu.

4.2-2 Use the ▲/▼ buttons on the Transition Detector on/off menu to select TURN ON. The ENTER PASSWORD BOX (small) will be displayed.

4.2-3 Use the ▲/▼/◄/► buttons to enter a PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.

4.2-4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to

display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time. After the PASSWORD has displayed for about 20 seconds the screen will return to the Transition Detector on/off menu.

Pressing the ENTER button on the remote control or

the INPUT button on the projector will close the PASSWORD BOX.

NOTE : Please do not forget your Transition Detector PASSWORD.

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content Contents of package How to use the Slot cover lockFastening the lens cover Projector featuresPreparations Part names Bottom sideCR/PR ComponentCB/PB Magnify Remote controlControl buttons Setting up Arrangement Min Max DownAdjusting the projectors elevator Elevator feetSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach Connecting your devices About Plug-and-Play capabilityUSB Connecting to a Network and USB MemoryExamples of connection with a computer CB/PB CR/PRConnecting power supply AC inlet Connector Power cordInserting an SD Card and USB Memory Remote control Putting batteriesUsing the remote control Changing the signal setting for the projectors remote sensorTurning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundSelecting an input signal Searching an input signalAdjusting the zoom and focus  For a no signal For an RGB signal Using the automatic adjustment featureAdjusting the position  For a video signal or s-video signalUsing the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Move pointerMenu button Enter button Cursor buttons Reset button Multifunctional settingsUsing the menu function Easy MenuEasy Menu Easy Menu Light ó Dark Adjust the level using the buttonsPicture Menu GammaPicture Menu Color TempMY Memory Over Scan PhaseImage Menu PositionSize Auto AdjustImage Menu Video NR Input MenuProgressive Color SpaceVideo Format Input MenuComponent Frame LockCustom Resolution Setup Menu Volume Setup MenuUsing the buttons / switches the mode for mirror status AudioBlank Screen MenuMenu Position MyScreen Screen MenuStart UP MyScreen LockMessage No Input is DetectedSync is OUT of Range Source NameAuto Search Option MenuTurn on  Turn OFF Auto onLamp Time Option MenuAuto OFF MY ButtonGhost ServiceFAN Speed Filter MessageUse the / button to change the Projectors remote sensor Factory ResetRemote Freq InformationChanging the Password Using Security FeaturesInputting the Password SecurityTurning on the MyScreen Password Function Using the MyScreen Password FunctionDescription If you have forgotten your Password Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off Turning Off the PIN Lock Function If you have forgotten your PIN CodeTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off MIU Menu Live ModeSee Live Mode in User’s Manual Network Functions for PresentationMIU Menu Dhcp Dynamic Host Configuration ProtocolSetup OperationSubnet Mask Default GatewayIP Address Time DifferenceEncryption Network ModeMode SpeedMIU Restart Maintenance LampType number = DT00751 Case of replacement by yourselfLamp Handle Filter cover Air filterType number = NJ22222 Air filter Air filter’s knobWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page Internal temperature is rising TroubleshootingThere is no input signal Related messagesRegarding the indicator lamps Regarding the indicator lamps Signal cables are not correctly connected Electrical power cord is not pluggedPower switch is not set to the on position Signal source does not correctly workColor settings are not correctly adjusted Volume is adjusted to an extremely low levelAudio setting is not correct Color Space setting is not suitableWhisper function is working Not properly adjustedEither the focus and/or horizontal phase settings are Lamp is approaching the end of its product LifetimeWarranty and after-service SpecificationsSpecifications
Top Page Image Contents