Hitachi CP-X268A user manual Regarding the indicator lamps

Page 65

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP

TEMP

Description

indicator

indicator

indicator

 

 

 

 

 

 

 

 

The cooling fan is not operating.

Blinking

 

 

Please turn the power off, and allow the projector to

 

 

cool down at least 20 minutes. After the projector has

In Red

 

 

Turned

Blinking

sufficiently cooled down, please make confirmation

or

off

In Red

that no foreign matter has become caught in the fan,

Lighting

 

 

etc., and then turn the power on again.

In Red

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

 

 

 

please contact your dealer or service company.

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to

Blinking

 

 

cool down at least 20 minutes. After the projector has

 

 

sufficiently cooled down, please make confirmation of

In Red

 

 

Turned

Lighting

the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

 

 

 

If the same indication is displayed after the remedy,

 

 

 

please set FAN SPEED of the SERVICE item in the

 

 

 

OPTION menu to HIGH.

 

 

 

It is time to clean the air filter.

 

 

 

Please immediately turn the power off, and clean or

Lighting

Simultaneous

change the air filter referring to the section “Air Filter”.

In Green

blinking in Red

After cleaning or changing the air filter, please be sure

 

 

 

to reset the filter timer. After the remedy, reset the

 

 

 

power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C). After the treatment, reset

 

 

 

 

 

 

the power to ON.

Blinking in

 

 

At least 1 “Power ON” schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

(Please refer to the User’s Manual-Network Functions:

seconds

 

 

Schedule Settings for more information.)

NOTE • When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “” (OFF) side of the power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Content How to use the Slot cover lock Contents of packageFastening the lens cover Projector featuresPreparations Bottom side Part namesCR/PR ComponentCB/PB Magnify Remote controlControl buttons Setting up Min Max Down ArrangementElevator feet Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesUSB Connecting to a Network and USB MemoryExamples of connection with a computer CR/PR CB/PBAC inlet Connector Power cord Connecting power supplyInserting an SD Card and USB Memory Putting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlTurning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal  For a no signalAdjusting the position Using the automatic adjustment feature For an RGB signal  For a video signal or s-video signalCorrecting the keystone distortions Using the magnify featureTemporarily blanking the screen Freezing the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsMenu button Enter button Cursor buttons Reset button Easy MenuEasy Menu Easy Menu Picture Menu Adjust the level using the buttonsLight ó Dark GammaColor Temp Picture MenuMY Memory Image Menu PhaseOver Scan PositionSize Auto AdjustImage Menu Progressive Input MenuVideo NR Color SpaceComponent Input MenuVideo Format Frame LockCustom Resolution Setup Menu Using the buttons / switches the mode for mirror status Setup MenuVolume AudioBlank Screen MenuMenu Position Start UP Screen MenuMyScreen MyScreen LockSync is OUT of Range No Input is DetectedMessage Source NameTurn on  Turn OFF Option MenuAuto Search Auto onAuto OFF Option MenuLamp Time MY ButtonFAN Speed ServiceGhost Filter MessageRemote Freq Factory ResetUse the / button to change the Projectors remote sensor InformationInputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Function Setting the PasswordRegistering the PIN Code Using the PIN Lock FunctionTurning the Password off If you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Setting the Transition Detector off See Live Mode in User’s Manual Network Functions for Live ModeMIU Menu PresentationSetup Dhcp Dynamic Host Configuration ProtocolMIU Menu OperationIP Address Default GatewaySubnet Mask Time DifferenceMode Network ModeEncryption SpeedMIU Restart Lamp MaintenanceType number = DT00751 Case of replacement by yourselfLamp Handle Filter cover Air filterType number = NJ22222 Air filter’s knob Air filterWill come up. Remove the battery Put a new battery Replacing Internal Clock batteryTake the old battery out Page There is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps Power switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product LifetimeSpecifications Warranty and after-serviceSpecifications
Top Page Image Contents