Hitachi CP-X955W/E specifications Remove the battery compartment cover

Page 10

Names and functions of each part (continued)

How to insert batteries insert the provided batteries (LR6 (alkali)) into the remote control transmitter.

ÁRemove the battery compartment cover.

Slide the battery compartment cover in the direction of the arrow while pressing slightly down on it.

Caution Cautions on use of batteries

Do not use batteries not specified for this unit. Also do not use old and new batteries together. It may cause a fire, injury due to burst of battery or liquid leakage.

When inserting batteries, pay attention to the

direction of the and polarity indications and insert the batteries correctly. If the polarities are confused, it may cause injury or damage near the unit due to a burst of battery or liquid leakage.

ªInsert the batteries as

illustrated inside the battery compartment.

£ Replace the cover.

Caution Cautions on use

Do not drop the remote control transmitter or apply any shock to it.

Do not let the remote control transmitter get wet and do not put it on a wet object. It may cause a malfunction.

If you are not going to use it for a long time, remove the batteries from the remote control transmitter.

If operation of the remote control becomes difficult, replace the batteries.

Caution Cautions on use of the laser pointer.

The laser pointer on the remote control unit radiates the laser beam from the laser aperture.

This laser pointer used as a stick (for indication).

Do not stare directly into the laser aperture or radiate the laser beam to other persons as the laser emitted is a class II laser and it could damage you vision, etc.

Especially pay attention if children are present.

The three labels below are caution labels for the laser beam.

AVOIDE EXPOSURE–LASER

RADIATION IS EMITTED

FROM THIS APERTURE

LASER APERTURE

C A U T I O N

LASER RADIATION-

DO NOT STARE INTO BEAM

WAVE LENGTH:670nm

MAX. OUTPUT:1mW

CLASS II LASER PRODUCT

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE APPARECCHIO LASER DI CLASSE 2

RAYONNEMENT LASER

MANUFACTURED

NE PAS REGARDER DANS

 

LE FAISCEAU APPAREIL

August-97

A LASER DE CLASSE 2

 

LASER-STRAHLUNG

 

NICHT IN DEN STRAHL

 

BLICKEN LASER KLASSE2

MANUFACTURER:A

 

MADE IN JAPAN

10

Image 10
Contents Outline FeaturesContentsPage Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Video inputsDo not use power supplies Do not look directly at the lens when the lamp is litLDo not install this unit in an unstable LIf any abnormality occursBe careful in handling the power cord Do not stare directly into the laser ApertureClean inside the unit at least once two years Handle the power cord carefullyCleaning When you are not going to use for a long timeCleaning the lens Do not place this unit where it gets hotVolume Cleaning the cabinetMain unit Names and functions of each partStandby / on Laser on Remote control transmitterDisk PAD Remove the battery compartment cover View from the top View from the side InstallationInstallation of liquid crystal projector View from the front View from the sideBasic operations To project the picturePlug & Play Press the STANDBY/ON button, for 1 secondAdjustments and functions Press the Menu buttons or the Menu on / OFF buttonColor SET UPBrightness SizeInput ImageBlank OPT. OptionReveal Language COM. BitsConnection to the video signal terminals Connection to the RGB signal terminalConnection to the RGB signal terminal Example of computer signalInitial set signals Data HsyncControl signal terminal Connection to the control signal terminalMouse emulation Connection to the control signal terminal Control command code CommunicationControl data table Procedure of getting the Projector status Cleaning the air filter Example of system setupConnecting various equipment Lamp Clean the air filter using a vacuum cleanerRe-install the air filter Message tableWhen you think something wrong Indicator displayDimension diagram