Hitachi CP-X955W/E specifications Control data table

Page 25

Connection to the control signal terminal (continued)

				Control data table
Item	Data code

MOUSE	00h=stop mouse emulation. 01 ∼ 7Fh=start mouse emulation

COMMUNICATE	0Xh=8N1
	1Xh=7N1
	X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps

POWER	1Eh=Power off (Standby mode), 1Fh=Power on

ZOOM	01-3Fh=Zoom +, 41-7Fh=Zoom- 01, 04 (up) ∼ 3F, 7F (down)

FOCUS	01-3Fh=Focus +, 41-7Fh=Focus- 01, 04 (short) ∼ 3F, 7F (long)

MIRROR	00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H & V:Invert

INPUT	11h=VIDEO1, 12h=VIDEO2, 21h=RGB1, 22h=RGB2

VIDEO SYSTEM	00h	00h=Auto, 00h 01h=NTSC, 00h 04h=NTSC4.43
	00h	02h=PAL, 00h 03h=SECAM, 00h 05h=M-PAL

VOLUME	00h (min) ∼ 7Fh (max)

MUTE	00h=Mute off, 01h=Mute on

BRIGHT	00h	00h	00h	(dark) ∼ 00h 00h 7Fh (brite)

CONTRAST	00h	00h	00h	(lower) ∼ 00h 00h 7Fh (higher)

COLOR	00h	00h	20h	(less) ∼ 00h 00h 60h (more)

TINT	00h	00h	2Eh (red) ∼ 00h 00h 52h (green)

SHARPNESS	00h	00h	00h	(soft) ∼ 00h 00h 64h (sharp)

H.PHASE	00h	00h	00h ∼ 00h 00h 1Fh

H.POSIT	00h	00h	52h	00h (left) ∼ 00h	00h 54h 04h (right)

H.SIZE	00h	00h	00h	06h (narrow) ∼ 00h 00h 48h 0Bh (wide)

V.POSIT	00h	00h	06h	00h (down) ∼ 00h 00h 50h 05h (up)

BLANK	0Xh=Blank off
	1Xh=Blank on
	bit0 0=Blue off, 1=Blue on,				bit1 0=Green off,	1=Green on
	bit2 0=Red off, 1=Red on,				bit3 0=Not change,	1=Change

REVEAL	X1h=Reveal down, X4h=Reveal right, X=0 (slow) ∼ 7 (fast)

Caution If computer sends the undefined command code or data code, Projector can not guarantee operation.

Command is consisted of 2 command bytes and following data bytes. 1-st byte indicates the kinds of commands and the length of command.

‘0xH’ : Error-reply	Projector sends to computer.
‘1xH’ : Command reply	Projector sends to computer.
‘2xH’ : Ask command	Computer sends to Projector.
‘3xH’ : Set command	Computer sends to Projector.
‘4xH’ : Default set command	Computer sends to Projector.

‘5xH’ — ‘FxH’ : Reserved

‘x’ indicates the length of data bytes.

2-nd byte indicates the command code ‘yy’ as command table. Data table shows the data byte.

25

Image 25

Contents ContentsPage FeaturesOutline Operating GuideFor the Customers in U.K Power cord Video signal cablesBefore use Video inputsLDo not install this unit in an unstable Do not look directly at the lens when the lamp is litDo not use power supplies LIf any abnormality occursDo not stare directly into the laser Aperture Be careful in handling the power cordCleaning Handle the power cord carefullyClean inside the unit at least once two years When you are not going to use for a long timeVolume Do not place this unit where it gets hotCleaning the lens Cleaning the cabinetMain unit Names and functions of each partStandby / on Laser on Remote control transmitterDisk PAD Remove the battery compartment cover Installation of liquid crystal projector InstallationView from the top View from the side View from the front View from the sideTo project the picture Basic operationsPress the STANDBY/ON button, for 1 second Plug & PlayPress the Menu buttons or the Menu on / OFF button Adjustments and functionsBrightness SET UPColor SizeImage InputBlank OPT. OptionReveal COM. Bits LanguageConnection to the RGB signal terminal Connection to the video signal terminalsExample of computer signal Connection to the RGB signal terminalData Hsync Initial set signalsControl signal terminal Connection to the control signal terminalMouse emulation Connection to the control signal terminal Communication Control command codeControl data table Procedure of getting the Projector status Cleaning the air filter Example of system setupConnecting various equipment Re-install the air filter Clean the air filter using a vacuum cleanerLamp Message tableIndicator display When you think something wrongDimension diagram