Hitachi CP-X955W/E Do not step on this unit or do not put a Heavy object on it, Cleaning

Page 6

Caution

LDo not step on this unit or do not put a

heavy object on it.

Do not step on this unit. Especially pay attention if children are present.

If you do, the unit may fall over or

may be broken causing an injury.

Do not put a heavy object on this unit. If you do, the unit may fall due to its imbalance or it

may drop, causing an injury.

LDo not block the ventilation holes.

Do not block the ventilation holes. If the ventilation holes are blocked, the heat inside may build up and it may cause a fire. Do not use this

unit in the following ways: On its side. In a poorly ventilated, narrow place. On a carpet or bedspread. Covered with a tablecloth. Place this unit so that the ventilation holes are kept 10cm or more away from the wall.

LDo not place this unit in a moist or

dusty place.

Do not place this unit in a moist or dusty place. It may cause a fire, electric shock, etc.

Do not place this unit where it would be exposed to soot or steam,

near a cooking stove or humidifier,

etc. It may cause a fire, electric shock, etc.

LSet the caster stoppers.

When this unit is installed on the table with casters, set the caster stoppers. If the table moves, it may fall over, causing an injury.

L Handle the power cord carefully.

Do not bring the power cord near a heating

device. The shield of the cord may melt and it

may cause a fire, electric shock, etc.

Do not insert/disconnect the power

plug with wet hands. It may cause

LCleaning

Be sure to pull out the power plug from the power outlet for safety when cleaning.

LUse of batteries.

Pull out the power plug from the power outlet.

an electric shock.

When the power plug is to be disconnected, do not pull the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc.

Do not use batteries not specified for this unit. Do not use new batteries mixed

together with old ones. This may cause a fire, injury due to burst of battery, liquid leakage.

When inserting batteries in this unit, pay

attention to the direction of the and polarity indications and insert the batteries correctly. If the polarities are confused, it may cause injury or damage near the unit due to burst batteries, liquid leakage, etc.

Be sure to hold the power plug.

LClean inside the unit at least once two years.

Ask your dealer to clean inside the unit at least once two years. If the unit is left with too much

dust inside as it is for a long this without cleaning, it may cause a fire. Especially it is

effective to clean before the rainy

season starts. Consult your dealer for the cost of the cleaning the inside

the unit.

LWhen you are not going to use for a long time.

L Caution when carrying it.

When this unit is to be moved, apply a

When you are not going use this unit for a long time because you are going on a trip, etc., be sure to pull out the power plug from the power outlet for safety. And also apply cover to the lens so that the lens is not damaged.

6

Pull out the power plug from the power outlet.

cover to the lens and be sure to

disconnect the power plug from the

power outlet and check that all external

connection cords are removed before

moving it. If not, the cord may be

damaged and it may cause a fire,

electric shock, etc.

Pull out the power plug from the power outlet.

Image 6
Contents Outline FeaturesContentsPage Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Video inputsDo not use power supplies Do not look directly at the lens when the lamp is litLDo not install this unit in an unstable LIf any abnormality occursBe careful in handling the power cord Do not stare directly into the laser ApertureClean inside the unit at least once two years Handle the power cord carefullyCleaning When you are not going to use for a long timeCleaning the lens Do not place this unit where it gets hotVolume Cleaning the cabinetNames and functions of each part Main unitStandby / on Remote control transmitter Laser onDisk PAD Remove the battery compartment cover View from the top View from the side InstallationInstallation of liquid crystal projector View from the front View from the sideBasic operations To project the picturePlug & Play Press the STANDBY/ON button, for 1 secondAdjustments and functions Press the Menu buttons or the Menu on / OFF buttonColor SET UPBrightness SizeInput ImageOPT. Option BlankReveal Language COM. BitsConnection to the video signal terminals Connection to the RGB signal terminalConnection to the RGB signal terminal Example of computer signalInitial set signals Data HsyncConnection to the control signal terminal Control signal terminalMouse emulation Connection to the control signal terminal Control command code CommunicationControl data table Procedure of getting the Projector status Example of system setup Cleaning the air filterConnecting various equipment Lamp Clean the air filter using a vacuum cleanerRe-install the air filter Message tableWhen you think something wrong Indicator displayDimension diagram