Hitachi CP-X955W/E Connection to the RGB signal terminal, Example of computer signal

Page 20

Connection to the RGB signal terminal (continued)

3. Example of computer signal

	Resolution		fH	fV	Standard	Note 1	Note 2	Note 3	Display Dots
	H × V		(kHz)	(Hz)	Type	Note 1	Note 2	Note 3	H × V
	H × V		(kHz)	(Hz)	Type				H × V

	640 × 350		31.5	70.1		VGA-1		Expanded	1024 × 560

	640 × 400		24.8	56.4		NEC		Expanded	1024 × 640
	640 × 400		24.8	56.4		PC9800		Expanded	1024 × 640
						PC9800

	640 × 400		31.5	70.1		VGA-2		Expanded	1024 × 640

	640 × 480		43.3	85.0	VESA			Expanded	853 × 640

	640 × 480		31.5	59.9	VESA	VGA-3		Expanded	1024 × 768

	640 × 480					Mac 13˝	SW 1 ON		1024 × 768
			35.0	66.7		Mac 13˝	SW 5 ON	Expanded
			35.0	66.7		mode	SW 5 ON	Expanded
						mode	SW 6 ON
							SW 6 ON

	640 × 480		37.9	72.8	VESA			Expanded	1024 × 768

	640 × 480		37.5	75.0	VESA			Expanded	1024 × 768

	800 × 600		35.2	56.3	VESA	SVGA (56Hz)		Expanded	1000 × 750

	800 × 600		37.9	60.3	VESA	SVGA (60Hz)		Expanded	1000 × 750

	800 × 600		48.1	72.2	VESA	SVGA (72Hz)		Expanded	1000 × 750

	800 × 600		46.9	75.0	VESA	SVGA (75Hz)		Expanded	1000 × 750

	800 × 600		53.7	85.1	VESA	SVGA (85Hz)			800 × 600

	832 × 624		49.7	74.5		Mac 16˝	SW 2 ON	Expanded	980 × 735
						Mac 16˝	SW 5 ON
						mode	SW 5 ON
						mode	SW 6 ON
							SW 6 ON

	1024	× 768	48.4	60.0	VESA	XGA (60Hz)			1024 × 768

	1024	× 768	56.5	70.1	VESA	XGA (70Hz)			1024 × 768

	1024	× 768	60.0	75.0	VESA	XGA (75Hz)			1024 × 768

	1152	× 864	67.5	75.0	VESA			Compressed	988 × 741

	1280	× 960	60.0	60.0	VESA			Compressed	1024 × 768

	1280	× 1024	64.0	60.0	VESA	SXGA (60Hz)		Compressed	960 × 768

	1280	× 1024	80.0	75.0	VESA	SXGA (75Hz)		Compressed	960 × 768

Note 1 : Signal mode

Note 2 : MAC adapter is necessary to the resolution mode.

Projector is compatible with 13 inch mode and 16 inch mode.

MAC 13" mode = switch 1, switch 5 and switch 6 are ON. MAC 16" mode = switch 2, switch 5 and switch 6 are ON.

Note 3 : Display mode

ON

1 2 3 4 5 6

(Example 16inch mode)

Caution • Some input source may not be displayed properly because they are not compatible with the projector.

• Some input source may not be displayed in full size as shown “Display Dots”.

20

Image 20

Contents Features ContentsPageOutline Operating GuideFor the Customers in U.K Video signal cables Power cordBefore use Video inputsDo not look directly at the lens when the lamp is lit LDo not install this unit in an unstableDo not use power supplies LIf any abnormality occursBe careful in handling the power cord Do not stare directly into the laser ApertureHandle the power cord carefully CleaningClean inside the unit at least once two years When you are not going to use for a long timeDo not place this unit where it gets hot VolumeCleaning the lens Cleaning the cabinetStandby / on Names and functions of each partMain unit Disk PAD Remote control transmitterLaser on Remove the battery compartment cover Installation Installation of liquid crystal projectorView from the top View from the side View from the front View from the sideBasic operations To project the picturePlug & Play Press the STANDBY/ON button, for 1 secondAdjustments and functions Press the Menu buttons or the Menu on / OFF buttonSET UP BrightnessColor SizeInput ImageReveal OPT. OptionBlank Language COM. BitsConnection to the video signal terminals Connection to the RGB signal terminalConnection to the RGB signal terminal Example of computer signalInitial set signals Data HsyncMouse emulation Connection to the control signal terminalControl signal terminal Connection to the control signal terminal Control command code CommunicationControl data table Procedure of getting the Projector status Connecting various equipment Example of system setupCleaning the air filter Clean the air filter using a vacuum cleaner Re-install the air filterLamp Message tableWhen you think something wrong Indicator displayDimension diagram