Kodak i30 / i40 manual EMC statements, United States, Japan

Page 7

EMC statements

United States		This equipment has been tested and found to comply with the limits for
		a Class B digital device pursuant to Part 15 of the FCC rules. These
		limits are designed to provide reasonable protection against harmful
		interference in a residential installation. This equipment generates,
		uses, and can radiate radio frequency energy and, if not installed and
		used in accordance with the instruction manual, may cause harmful
		interference to radio communications. However, there is no guarantee
		that interference will not occur in a particular installation. If this
		equipment does cause harmful interference to radio or television
		reception, which can be determined by turning the equipment off and
		on, the user is encouraged to try to correct the interference by one or
		more of the following measures:
		- Reorient or relocate the receiving antenna.
		- Increase the separation between the equipment and receiver.
		- Connect the equipment into an outlet on a circuit different from
		that to which the receiver is connected.
		- Consult the dealer or an experienced radio/TV technician for
		additional suggestions.
		Any changes or modifications not expressly approved by the party
		responsible for compliance could void the user’s authority to operate
		the equipment. Where shielded interface cables have been provided
		with the product or specified additional components or accessories
		elsewhere defined to be used with the installation of the product, they
		must be used in order to ensure compliance with FCC regulation.
Japan		This is a Class B product based on the standard of the Voluntary
		Control Council for interference by information Technology Equipment
		(VCCI). If this is used near a radio or television receiver in a domestic
		environment, it may cause radio interference. Install and use the
		equipment according to the instruction manual.

4	A-61512 May 2006

Image 7

Contents User’s Guide Contents Maintenance Introduction Scanner features Safety and regulatory Safety informationAgency approvals United States EMC statementsJapan European Union Power systemAcoustic emission ConnectionWhat’s in the box System requirements Getting StartedAttaching the input tray Select Install Scanner Software Installing the Kodak Driver SoftwareAttaching the output tray and special document feeder Page Page Select USB Test United States Canada China power cord Cable Connecting the USBPage Software Installing applicationFront view Scanner componentsBack view Inside viewTurning the scanner on and off Adjusting the input and output traysFront-feed minimum/center alignment 6.35 x 5.08 cm 2.5 x 2.0 Start and stop scanningVerifying your scanner installation Page Page Application software Viewing test imagesManager Configuring functionsPage Configuring Readiris InstallingSelect Scanner Model Page Numbers Assigning functionUsing function numbers Scanning your documents Scanning documents using the special document feeder Common terms OverviewBi-tonal or Binary black-and-white Color Making cameraSelections Example 1 scanning a two-sided color document both sidesStarting the Scan Validation Tool Scan Validation Tool dialog box Kodak Scanner Properties dialog box Using the Twain DatasourceButtons on the Kodak Scanner Properties dialog box Imaging tab Page Disabled No Noise Filter Used Dpi 80 Threshold 200 dpi Contrast 100 Page Page Cropping values Paper tabPage 61512 May Page Better, Best, Superior Dropout tabRemove Red, Remove Green, Remove Blue Multifeed tab Options tab Tool, via the Twain Datasource Setup tabInfo tab Box Using the Isis DriverScanner Settings dialog Settings dialog boxCamera Settings area Page Page Fixed thresholding ATP disabled Dpi 80 Threshold 20 Contrast Dpi 80 Threshold 100 Contrast More Scanner Settings dialog box Image Control options Black on White polarity White on Black polarity Color Dropout options Options Scanner ControlDialog box Multi-Feed DetectionDefining the Scan area Area Maintenance Cleaning the feed module Cleaning the rollersCleaning the calibration area Module Replacing the feedSupplies and consumables Clearing a document jam Indicator lights and error codesProblem Possible Solution Problem solving61512 May Scanner not working Page Page Connection Testing for a USB\program files\Kodak\Document Imaging\usbtst.exe Your operating system only supports USB SolutionsUSB will not work You do not need to install any additional USB cardsAppendix a Specifications Eastman Kodak Company