Fluke Network Tester user manual Inline between a PoE Powered Device and the Network

Page 37

AutoTest

Running AutoTest 3

To get detailed results, move the cursor to one of the following icons then press SELECT:

•PC icon : enables you to view results for the device. Go to Chapter 4 “Troubleshooting a Network Device” for details.

•Network icon : enables you to view network results. Go to Chapter 5 “Troubleshooting Networks” for details.

You can view additional results by selecting items from the Main menu below the diagram.

Inline between a PoE Powered Device and the Network

During AutoTest, NetTool checks for a network on one side and an Ethernet termination on the other. If this configuration is found, the sides are connected together for up to 20 seconds while NetTool searches for a link pulse. This enables an Ethernet-powered device to power up and source link to complete the connection.

If NetTool is connected between a PoE-powered device and the network, a diagram similar to the one shown in Figure 3-6 is displayed.

ahn311s.bmp

Figure 3-6. Inline Connection Between a PoE-Powered

Device and the Network

The diagram in Figure 3-6 also shows the speed of the link. Icons represent duplex settings (see Table 3-2) and link and polarity levels (see Table 3-3). Status information is displayed in the area below “AutoTest”.

To get detailed results on the network, select the Network

icon .

For VoIP-specific information, see Chapter 7 “Verifying Voice over IP Service”.

3-7

Image 37

Contents NetTool Limited Warranty and Limitation of Liability Table of Contents NetTool Iii Common Problems Appendices NetTool List of Tables Viii List of Figures NetTool Introduction Using This Manual What is NetTool?NetTool Features Care and MaintenancePackage Contents Optional Accessories Service and AdjustmentRegistering NetTool Contacting Fluke Networks PC/NetTool Link Utility ProgramsNetTool Blaster Getting Acquainted Installing and Running the Link UtilitiesNetTool Toolkit Turning on NetToolUnderstanding the LEDs Link/Collision/Error LEDUtilization LED Icons NetTool MenusMain Menu Navigation Keys ScrollingMaximizing Battery Life Power SupplyInstalling the Batteries Using the AC AdapterUpdating NetTool’s Software Configuring NetTool Setting Up and Connecting NetToolIntroduction Settings Menu Changing the System SettingsManually Assigning NetTool an IP Address Identifying Unwanted ProtocolsCreating a List of IP Addresses to Ping Selecting a Language for the Display ScreensObtaining Information about Your NetTool Connecting a Patch Cable Connecting NetToolSingle-Ended Connection Single-Ended Connection into a Wall Jack Inline Connection between a PC Network Inline ConnectionSerial Port Connection Recommended speed setting for the serial port isRunning AutoTest AutoTestCable Test Results WiremapCable Length, Opens, Shorts, and Splits Network Drop Single-Ended AutoTest ResultsNetwork Device Services NetTool Discovers DeviceInline between a Device and the Network Inline AutoTest ResultsLink and Polarity Level Indicator Definition Inline between a PoE Powered Device and the Network NetTool Verifying a Device’s Configuration Troubleshooting a Network DeviceViewing Link Status Information Link Configuration DetailsHealth Details Checking Frames for ErrorsSelect Protocols Screen Tracking ProtocolsAddresses Used Screen Obtaining a Device’s IP Address InformationVlan Information Identifying Network ResourcesNetTool Finding Out About Your Network Troubleshooting NetworksSegment ID Screen Identifying the Network TypeIdentifying Key Devices Troubleshooting NetworksPinging a Single Device PingAssigning an IP Address to NetTool Ping Pinging Multiple DevicesPing Results Screen Displaying the Problem Log Common ProblemsProblem Log Understanding the Problem Log DisplayLink Connectivity Problems Problems NetTool DetectsThings to Consider Problem Transmit pair open Health Problems Network ProblemsNetWare Problem Ethernet frame-type mismatchesTCP/IP Host ConfigurationProblem Wins resolution failed Name ResolutionNetBIOS Web Problem PC involved in MB electionsPrinter Problem Unable to connect to POP3 serverUnwanted protocols when enabled Verifying Voice over IP Service Viewing Vlan and CDP Information Viewing PoE Voltage and Pair InformationVoIP Log VoIP LogRTP drop Viewing Call Quality MeasurementsBefore You Begin Creating and Managing ReportsReporter Menu Creating a ReportDeleting or Overwriting a Report NetTool Appendix Title AppendicesPage General Specifications SpecificationsEnvironmental Requirements Temperature ApprovalsSample VoIP Call Logs Dhcp ACK Typical Cisco Skinny Sccp Phone BootupAppendices Start Media Xmit Typical Cisco Skinny Sccp Call LogSample VoIP Call Logs B Typical Cisco Skinny Sccp Call Log Typical SIP Phone Bootup Log Typical SIP Phone Bootup Log Typical SIP Call Log Typical SIP Call Log 10BASE2 Glossary802.3 Access MethodAnomaly 802.2Bridge Switch ARP Address Resolution ProtocolCharacteristic impedance AttenuationCollision ClientCrossed Pair CrosstalkEIA568 Destination AddressEncapsulation EthernetHalf-Duplex Full-DuplexIcmp Internet Control and Message Protocol IP Internet ProtocolJitter JabberLAN Local Area Network Late CollisionPing NIC Network Interface CardNode Number NVP Nominal Velocity of PropagationRemote Collision RJ-45 ConnectorRepeater Router or GatewaySignal/Noise Ratio SAP Service Advertising ProtocolRtcp Real-time Transport Control Protocol RuntsSnmp Simple Network Management Protocol Snap Subnetwork Access ProtocolSource Address Split PairUptime TopologyTransport TransceiverIndex NetTool Index NetTool